Attwood 3592 Marine Lighting User Manual


 
LED Bi-Color Pole Light
Model 3592
SAVE THESE INSTRUCTIONS
Form Number 69435 Rev. A 08-05
© 2008 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com
Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards as tested by
Imanna Laboratories, 2/29/2008. 1 nautical mile visibility.
CAUTION
Read all instructions carefully before installing and using this product. All positive (+12V DC) lighting
wires require a 1-amp fuse to protect circuits and vessel. The aluminum light pole is not grounded.
MAKE SURE POWER SOURCE IS 12-VOLT DC ONLY. HIGHER VOLTAGE WILL
DAMAGE LIGHT AND CIRCUITRY.
WARNING
Disconnect power when installing or servicing this product. Remove boat from water before using
any 120V AC power tools.
LOCATION
Lights must be mounted to an unobstructed smooth surface on the gunwale, deck or superstructure.
Locate Bi-Color Combination Light in an area as far forward as possible. (Figure 1)
INSTALLATION
Bases That Do Not Use Locking Collars
1. Align pole screw with the slot (or locking spring) in the existing base. Insert pole into base (Figure 2).
2. Press down fi rmly to engage electrical connectors. With Easy Lock Base, be sure locking spring
clicks over pole screw.
3. To remove:
• Pull locking spring back (on Easy Lock Base)
• Pull pole straight up.
Bases That Use Locking Collars
1. Align pole screw with the slot (or locking spring) in the existing base. Insert pole into base (Figure 3).
2. Press down fi rmly to engage electrical connectors. With Easy Lock Base, be sure locking spring
clicks over pole screw.
3. Slide locking collar down to base, rotate until you can insert lower ring inside top of base.
NOTE: Locking Collar stays above the Easy Lock Base
4. On bases other than the Easy Lock Series, press collar down into base and rotate until it tightens
between pole and base.
NOTE: Periodically check pole to make sure it is secure.
5. To remove:
• Pull locking spring back (on Easy Lock Base)
• On other bases, rotate locking collar in opposite direction until it loosens,
• Pull pole straight up.
TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR
1. For bases that do not accept locking collar, remove screw at bottom of pole. Slide locking collar
off end of pole.
2. Replace screw in the upper screw hole.
OPERATION
After installation, check lights to verify proper operation. Regulations require lights to be operated
with a three-position switch for:
1. Running lights (bow lights and all-round light);
2. Anchor lights (all-round light only);
3. Off.
BASE WIRING
IMPORTANT: LED-based lights MUST be wired for correct polarity (Figure 4). If your light does not
function after installation, the light base may require re-wiring. To re-wire if necessary:
1. Unscrew or remove the base so you can reach wiring.
2. Locate the connection between base wiring and the boat’s wiring harness.
3. Cut wires. Add waterproof splice to each wire end.
4. Reverse polarity by reversing original wire connection to the wire harness.
5. Temporarily plug light into the base to check operation.
6. Remove light and reinstall base.
NOTE: Do not use light pole as a fl agpole or handle.
MAINTENANCE
When not in use, store in Pole Light Storage Clips (Attwood #7571). Choose a storage location
where light will not be damaged or be in constant contact with water.
ATTWOOD LIMITED 10-YEAR WARRANTY
Because of the longevity of Attwood’s LED lighting technology, Attwood offers a limited 10-year
warranty on this LED lighting product. See Product Catalog or attwoodmarine.com for details.
Figure 1 / Figura 1
Abbildung 1 / Figur 1
Figure 1
A. Red
B. Green
Figure 1
A. Rouge
B. Vert
Figura 1
A. Rojo
B. Verde
Abbildung 1
A. Rot
B. Grün
Figur 1
A. Röd
B. Grön
AB
Figure 2
A. Pole Screw
B. Locking Spring
C. EASY LOCK BASE
Figure 2
A. Vis du mât
B. Ressort de verrouillage
C. BASE FACILE À BLOQUER
Figura 2
A. Tornillo del asta
B. Resorte de seguridad
C. BASE DE AJUSTE FACIL
Abbildung 2
A. Schraube des Ständers
B. Sicherungsfeder
C. EASY LOCK BASE
Figur 2
A. Stångskruv
B. Låsfjäder
C. EASY LOCK BASE
Figure 2 / Figura 2
Abbildung 2 / Figur 2
A
B
C
Figure 3
A. Locking Collar
B. Lower Ring
C. Screw
D. #91020, #91024 or #91026
E. #91022
Figure 3
A. Bague de blocage
B. Bague inférieure
C. Vis
D. N° 91020 91024 ou 91026
E. N° 91022
Figura 3
A. Collarín de seguridad
B. Anillo inferior
C. Tornillo
D. Números 91020, 91024 ó 91026
E. Número 91022
Abbildung 3
A. Verriegelungszylinder
B. Unterer Ring
C. Schraube
D. Nr. 91020, Nr. 91024 oder Nr. 91026
E. Nr. 91022
Figur 3
A. Låskrage
B. Undre ring
C. Skruv
D. #91020, #91024 eller #91026
E. #91022
Figure 3 / Figura 3
Abbildung 3 / Figur 3
D
A
B
C
E
Figure 4 / Figura 4
Abbildung 4 / Figur 4
Figure 4
A. Black to -12 Volt
B. Gray to +12 Volt Navigation LIght Switch
with Fuse
Figure 4
A. Noir à la connexion négative de 12 volts
B. Gris à l’interrupteur du feu de navigation
positif de 12 volts avec fusible
Figura 4
A. Cable negro a -12 voltios
B. Cable gris al interruptor de luz para
navegación con fusible, +12 voltios
Abbildung 4
A. Schwarz bis - 12 Volt
B. Grau bis + 12 Volt Schalter für das
Navigationslicht mit Sicherung
Figur 4
A. Svart till -12 V
B. Grå till +12 V strömbrytare för navigationsljus
med säkring
B
A