Filter
Top Products
Style 409-R Mounting Kit
Thank you for purchasing a Shakespeare antenna product.
Customer comments are welcome. Before installing, please study
the diagram and check parts supplied against those listed.
IMPORTANT! Please read all instructions
before installing.
The Style 409-R Mounting Kit is a versatile antenna
mounting kit comprised of a Shakespeare Style 407 Heavy Duty
4-Way Swivel Mount and a Shakespeare Style 408-R Standoff
Bracket. The swivel mount permits mounting on almost any
surface, vertical or horizontal, and allows antenna laydown
in any desired direction. For use with 1½” antennas, and
antennas of 1
1
/
8
” and 1” diameter by using the appropriate
adapter (supplied) in the standoff bracket.
Tools required: Drill and drill bit for ¼” screws;
screwdriver; wrench or pliers
Installation Instructions
Choose an antenna mounting location that is as high as
feasible, as free as possible from obstructions, and as far as
possible from other antennas and strong sources of RF.
1. Using the base of the Swivel Mount as a template, mark the
location for the four mounting holes. Drill ¼” holes.
Note: When drilling berglass, place a wooden backup block
behind the surface if possible, to minimize push-through
damage.
2. Assemble the Swivel Mount by joining its two sections and
securing them with the hex-head bolt, washer, lockwasher and
nut (supplied). This joint can be in two positions, according to
whether you’re mounting to a vertical or horizontal surface.
3. Attach the Swivel Mount to the mounting surface using
hardware (not supplied) that is applicable to the mounting
surface.
IMPORTANT: If the thickness of the mounting
surface is not adequate to support the antenna
under expected stress, a wooden back-up pad
(not supplied) should be applied underneath the
mounting surface during installation.
4. Assemble the antenna to the Swivel Mount, being careful not
to damage the antenna’s cabling, if any.
5. Loosen the wing nut on top of the Standoff Bracket and slide
the retainer bar out of the way. Gently place the antenna in
its mounting position in the U-shaped opening in the bracket.
For 1
1
/
8
” and 1” antennas, put the appropriate reducing adapter
(supplied) in the opening.
©2002 Shakespeare Co. · Form I-409-R J: rev. 04/25/2010
* Not supplied. For some types of mounting surfaces you might need
stainless steel woodscrews or other hardware.
Wing Nut
Retainer Bar
Lockwasher*
Standoff Bracket
Assembly
Mounting
Screw*
Washer*
Nut*
Reducing Adapter
Antenna
STANDOFF
BRACKET
1”-14 Thread
Mounting Hole
Mounting
Screw*
Lockwasher*
Nut*
Bolt
Bolt
Base Plate
Swivel
Mounting
Screw*
Lockwasher*
Nut*
Deck Mounting: SIDE VIEW
Bulkhead
Mounting:
FRONT
VIEW
Bulkhead Mounting: SIDE VIEW
Supplied Parts
1 Standoff Bracket assembly
1 1” Reducing adapter
1 1
1
/
8
” Reducing adapter
1 Swivel Mount assembly
1 Mount base plate
1
3
/
8
“ Hex-head Bolt
1
3
/
8
“ Internal Tooth Lockwasher
1
3
/
8
“ Plain Washer
1
3
/
8
“ Hex Nut
35-90-1267-00
Shakespeare Electronic Products Group
U.S. Operations: 6111 Shakespeare Rd. · Columbia, SC 29223 · 803-227-1590 · Fax: 803-419-3099 · www.shakespeare-marine.com
U.K. Operations: Enterprise Way, Fleetwood, Lancashire, FY7
8RY, England · +44 (0) 1253 858787 · Fax: +44 (0) 1253-859595 · www.vtronix-antennas.com
Shakespeare is a subsidiary of Jarden Corporation (NYSE: JAH)