Filter
Top Products
Attwood
Subsidiary Steelcase Inc.
1016 N. Monroe Street, Lowell, MI 49331-0260
© 2000
1.Connect one lead to the negative (-) post of the 12-volt supply.
Connect the other lead to a fused and switched positive (+) 12-volt
supply. Sidelights require 1-amp fusing per lamp: a 1-amp fuse
for the Bicolor Combination light, a 2-amp fuse for the Sidelight
Pair. Note that navigation rules require sidelights to be operated
separately from anchor lights. Use either two switches or a single
switch with three positions for off/anchor/running (See Figure 3).
2-Amp Fuse
Switch
Figure 3
2.Check gasket to be sure the hole lip is down. Feed wires and
connectors down through the gasket (See Figure 4).
3.Be sure base is seated into the gasket ring all the way around
(See Figure 4 Detail).
4.Align base so the hole lip fits down into the wire clearance hole.
Insert two #10 stainless steel mounting screws and fasten them
to the deck. Note: Do not fasten screws so tightly that the gasket
is deformed.
5.To replace lens: Be sure O-ring is seated on the base screw
mount. Seat lens so the base tabs fit in the lens grooves and
base screw mount lines up with the lens screw hole. Be sure
the gasket is
outside
the lens at the back.
Figure 4
6.Place stainless steel cover over lens. Be sure gasket is
inside
the stainless steel cover at the back. Reinstall screw into cover
(See Figure 5).
ATTWOOD LIMITED WARRANTY
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331
(“Attwood”) warrants to the original consumer purchaser that Attwood brand
products will be free from defects in materials and workmanship under normal
use and service for one year from the date of original consumer purchases.
This limited warranty is not applicable if the product has been damaged by
accident, improper installation, unreasonable or improper use, lack of proper
maintenance, unauthorized repairs or modifications, normal wear and tear,
or other causes not arising out of defects in materials or workmanship.
Attwood products are warranted for use on pleasure boats. Any other use—
including but not limited to commercial, racing, or non-marine use—are not
covered under this warranty. Attwood’s obligation under this warranty is limited
to repair of the product at Attwood’s plant or replacement of the products at
Attwood’s option without expense to the original consumer purchaser. Any
expenses involved in the removal, reinstallation or transportation of the
product are not covered by this warranty.
The product must be returned to Attwood’s plant at the address above,
postage pre-paid, and insured with proof of original purchase including date.
If Attwood is unable to replace the product and repair is not commercially
practical or cannot be timely made, or if the original consumer purchaser
is willing to accept a refund in lieu of repair or replacement, Attwood may
refund the purchase price, less an amount for depreciation. The acceptance
by Attwood of any product returned or any refund provided by Attwood shall
not be deemed an admission that the product is defective or in violation of
any warranty. Products that are replaced or for which a refund is issued
become the property of Attwood.
THIS WARRANTY IS ATTWOOD’S ONLY EXPRESSED WARRANTY OF
THESE PRODUCTS. NO IMPLIED WARRANTY INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE EXTENDED BEYOND
THE WARRANTY PERIOD STATED ABOVE FOR EACH PRODUCT.
ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES, FOR LOSS
OF USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you may have other rights which vary from
state to state.
Gasket
Detail
Gasket
Hole Lip
Lens
Lens
Lens
Groove
Base
Base Tab
O-Ring
MAINTENANCE
To replace lamp: Remove the cover screw, cover, and lens.
You may need to pry the lens from the gasket with a small flat
screwdriver, starting in the front of the light.
Remove old lamp by rotating 1/8 turn counterclockwise and pulling
forward. Replace lamp with the proper bayonet bulb (Attwood Part
Number 912717). Check position of O-ring on the base screw mount.
Carefully replace lens and cover on gasket to maintain the waterproof
seal. Reinstall cover screw.
Gasket
Lens Cover
Figure 5