Open as PDF
Thank you for participating in the Belkin EcoPower Battery
Replacement Program™. Our program ensures that you receive the
correct battery for your UPS and your used battery is properly
recycled. Save the boxes and packaging material that your
replacement battery came in. You will need it to return your used
Warning! Before replacing your battery, please review this manual in
its entirety. If you have any issues, are technically challenged, have a
difficult time following instruction manuals or you cannot program
your VCR, STOP IMMEDIATELY, and contact Belkin Technical Support
at: (800) 223-5546 ext. 2263 or refer to a qualified computer
professional for assistance.
You should have received the following:
1. 1 Battery
2. EcoPower Instruction Manual
3. UPS Call Tag Label
One-year warranty on battery. Additional warranty programs available.
Please check belkin.com for updated information.
With the UPS plugged in, press and hold the On/Off/Test button for
more than three seconds until the "On Line" LED lights up to switch
the UPS on. The UPS will perform self-testing each time it is
switched on. Note: The UPS maintains the battery charge when in the
Press and hold the On/Off/Test button for more than three seconds
until the "On Line" or "On Battery" LED goes off.
Use the self-test to verify both the operation of the UPS and the
condition of the battery. In normal utility power, push the
“On/Off/Test” button less than two seconds and the UPS performs
a self-test function. During the self-test, the UPS operates in
During the self-test, the UPS briefly operates “on battery” mode (the
“Replace Battery” LED comes on). If the UPS passes the self-test, it
returns to “On Line” operation. The “Replace Battery” LED goes off
and the “On Line” LED goes on steady. If the UPS fails the self-test it
immediately returns to on-line operation and flashes the “Replace
Battery” LED. The loads are not affected. Recharge the battery
overnight and perform the self-test again. If the “Replace Battery”
LED is still on, the battery will need to be replaced; go to belkin.com.
In " BACK-UP" mode, push the On/Off/Test button less than three
seconds to silence the audible alarm. (The function is void when
under condition of "Low Battery".)
Step 1: Turn off your UPS by depressing and holding the
On/Off/Test button for more than 3 seconds until the “On
Line” or “On Battery” indicator light goes off. You will hear
a beep when your unit shuts off.
Step 2: Disconnect EVERY cord from your Belkin UPS.
Lay down the UPS. Use your thumb to open the battery
cover on the bottom of the unit.
Step 4: Grasp the tab attached to the battery and slide the battery out.
Step 5: Insert the replacement gently into the UPS. Make sure the battery
is well connected!
Step 6: Put the battery cover back and slide it into position.
Step 7: Connect your computer cords into the unit.
Step 8: Turn on UPS unit by depressing and holding down the
Additional recycling information is provided with your new battery
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL OR
CONTACT BELKIN COMPONENTS.
Battery Return Instructions
Step 1: Insert used battery into small box and seal with
Step 2: Place the boxed battery inside the bigger box. Please be
sure to cover the smaller box with the packing material. Seal the box
with packaging tape.
Step 3: Peel off the return label and place it onto the top of the box.
Step 4: Drop at UPS shipping center or UPS drop-off location.
On Line/On Battery
Low Battery/Replace Battery
BATTERY RETURN INSTRUCTIONS
BATTERY REPLACEMENT (CONTINUED)
Belkin Components USA
501 West Walnut Street
Compton • CA • 90220 • USA
Belkin Components, Ltd.
Unit 13 • Gatelodge Close
Round Spinney • Northampton • Northants
NN3 8RX • United Kingdom
Tel: +44 (0) 1604678300
Fax: +44 (0) 1604678330
Belkin Components, Ltd.
7 Bowen Cresent • West Gosford • NSW 2250 • Australia
Tel: +61 (2) 4372 8600
Fax: +61 (2) 4325 4277
© 2001 Belkin Components. All rights reserved. All trade names are
registered trademarks of respective manufacturers listed.