Filter
Top Products
21
Nothing Comes Close to a Cobra
®
Roger Beep Mode
Call Tone Select
VHF Marine Radio Protocols
Operating Your Radio
20
English
Setup Mode Programming
Call Tone Select continued
To Set Call Tone:
1. From the previous press of the Call/Enter/Setup button,
the LCD will display the letter “C” and the current Call
Tone number (01 through 10).
2. Press the Channel Up/Down button to select a different
Call Tone. An example of each call tone will sound for
1.5 seconds.
3. Press Call/Enter/Setup button to save this entry and
move to the next Setup mode programming.
NOTE: Call Tones are not usually used for Marine
VHF communications. We allow you to turn it On for
your unique communication needs.
Roger Beep Mode
In Roger Beep mode, your listener will hear an audible tone
when you release the Talk button. This alerts your listener
that you are finished talking and it is OK for them to speak.
To Set Roger Beep On or Off:
1. Display will show ROG icon and ON or OFF flashing.
2. Press Channel Up/Down button to select ON or OFF.
ROG will be displayed when On.
3. Press Call/Enter/Setup button to save this entry and
move to the next Setup mode programming.
Key Tone Mode
In Key Tone mode, an audible tone will sound each time a
button is pressed or you change a setting.
To Set Key Tone On or Off:
1.
Display will show Key Tone icon and ON or OFF flashing.
2. Press Channel Up/Down button to select ON or OFF.
3. Press Call/Enter/Setup button to save entry.
ATIS Mode
ATIS mode allows control over ATIS packet transmissions. This
mode is only visable after initial ATIS set-up (see page 25).
To Set ATIS On or Off:
1.
Display will show ATIS icon and ON or OFF flashing.
2. Press Channel Up/Down button to select ON or OFF.
3. Press Call/Enter/Setup button to save entry.
You have now ended Marine (VHF) Setup mode
programming and will enter Marine Standby mode.
NOTE: Scan and Tri-Watch features are not available
when ATIS is on.
VHF Marine Radio Protocols
Operating Your Radio
ATIS ID Programming
Key Tone Mode
ATIS ID Programming
•
The Automatic Transmission Identification System (ATIS) feature of this Cobra radio
is used to identify marine vessels in some inland waterways of European countries
that require ATIS transmission. An ATIS ID number is required to operate the ATIS
feature. The ATIS ID number is derived from your vessels call sign. You must enter
your ATIS ID number into this radio before the ATIS system will become functional.
Please consult your local dealer for questions about local ATIS requirements. The use of
ATIS is prohibited outside the European inland waterways covered by the Basel Agreement.
With this feature activated the vessels ATIS ID number is transmitted after every
push of the Talk button.
Channel Up/Down Button
ATIS ID Number Entry
To Set the ATIS ID Number:
NOTE
The ATIS ID is a 10 digit number that will always
begin with the number “9.” You will be asked to enter
only the last nine digits. The first digit, “9”, has been
automatically entered for you.
1. With the radio turned Off; press and hold the
Channel Down and SCAN buttons and
simultaneously power On the radio.
2. The LCD will display and flash the ATIS icon.
A dash (-), to the right of the digit “9”, will be
flashing for the next entry.
NOTICE
Remember, you only have one (1) attempt
to set the
ATIS ID number. Once this number has been entered,
only your Cobra distributor can reset the ATIS ID number.
You can also return the radio to Cobra for reprogramming.
3. Press the Channel Up/Down button to scroll through
the specific ATIS digit being entered.
4. Pressing the Call/Enter/Setup button advances to
the right, one (1) digit, for the next entry.
5. Repeat this input sequence until all nine digits have
been entered. The ATIS icon will stop flashing when
a successful ATIS ID entry has been made.
6. Press the Call/Enter/Setup button again, after all
numbers have been entered, to save the ATIS ID
number and return to the Marine Standby mode.
ATIS ID Start Screen
and SCAN Buttons
Channel Down
ATIS Mode
MRHH330EU_MANL_vC.qx:MRHH330_ENG_Body 12/28/09 10:04 AM Page 20