Filter
Top Products
2. To change the setting to 45°F (7°C) (blinking light
ON) touch and release the wet switch contacts
once more.Wait two seconds and then confirm that
the temperature reading on the Control Head has
changed to 45°F (7°C). Single touches will toggle
the setting between 40°F (4°C) and 45°F (7°C).
NOTE: When the LED is set to ON it will flash every four seconds
when the RSS is in operation (i.e. when the wet switch is
submerged). Even when the LED is set to ON, the LED will not
flash unless the wet switch is activated.If you want to test the RSS
to make sure the LED is set to ON before using the RSS, wet your
finger and hold it on the wet switch; if the LED is set to ON, the
LED will begin to flash.
NOTE: Repeat steps 1 and 2 to turn off the LED when finished
with night fishing.
3. Once you have made your selection you can either
wait 20 seconds for programming mode to time out
(the Start-Up screen will appear on the Control
Head display), or continue immediately to the next
procedure to change the channel.
Changing the Channel on the
Advanced RSS
To change the channel type on the Advanced RSS:
1. From the Light programming mode (see Turning
on the Advanced RSS Blinking Light), touch
and release the wet switch contacts twice more
with your moist finger to change from the Light
programming mode to the Channel programming
mode. The temperature reading on the Control
Head will change to show a temperature reading of
50°F (9°C) (channel set to A).
2. To change the setting to 55°F (12°C) (channel set
to B) touch and release the wet switch contacts
once more.Wait two seconds and then confirm that
the temperature reading on the Control Head has
changed to 55°F (12°C). Single touches will toggle
the setting between 50°F (9°C) and 55°F (12°C).
3. Once you have made your selection, wait 20
seconds for programming mode to time out (the
Start-Up screen will appear on the Control Head).
4. Use the SetUp Channel Select menu on the Control
Head to switch the software to match the new
channel designation on the Advanced RSS. See
Channel Select (SetUp Menu) for more information.
CAUTION: Make sure that you change the Channel Selection
on the Control Head to match the new Advanced RSS Channel
before using the Advanced RSS.
Using a First Generation RSS
First generation RSS units still sold with other SmartCast
®
products come in two versions, Channel A and Channel B
(RF40A and RF40B),and are both compatible with the RF35.
NOTE: When using either an RF40A or RF40B RSS with the
RF35,you will not get water temperature, and you will not be able
to turn on the LED or change the channel on the RSS. You will
still be able to read digital depth and bottom contour information.
NOTE: When using an RF40A or RF40B RSS, make sure to
select the matching channel from the CHANNEL SELECT
menu on the Control Head.
Maintenance
Your SmartCast
®
is designed to provide years of trouble-
free operation with virtually no maintenance. Follow these
simple procedures to ensure your SmartCast
®
continues to
deliver top performance.
WARNING! Never leave the RF35 SmartCast
®
product in a
closed car or trunk - the extremely high temperatures generated
in hot weather can damage the electronics.
Wrist Mounted Display Maintenance: If the Wrist
Mounted Display comes into contact with salt spray, wipe
the affected surfaces with a cloth dampened with fresh
water. When cleaning the protective lens on the display,
use a chamois and non-abrasive, mild cleaner. Do not
wipe while dirt or grease is on the lens. Be careful to avoid
scratching the lens. Do not use a chemical glass cleaner
on the lens, as this may cause it to crack.
RSS™ Maintenance: After using the RSS™ in salt
water, wipe the affected surfaces with a cloth dampened
with fresh water. The RSS™ Wet Switch™ pins must be
rinsed with fresh water after exposure to salt water to
prevent corrosion.
If your RSS™ remains out of the water for a long period of
time, it may take some time to wet it when returned to the
water. Small air bubbles can cling to the surface of the
RSS™ and interfere with proper operation. Wipe the face
of the RSS™ with a wet cloth to remove them.
Troubleshooting
Do not attempt to repair the RF35 Wrist Mounted Display
or RSS™ yourself. There are no user serviceable parts
inside, and special tools and techniques are required for
assembly to ensure the waterproof integrity of the
housings. Repairs should be performed only by authorized
Humminbird
®
technicians.
Many requests for repair received by Humminbird
®
involve
units that do not actually need repair. These units are
returned “no problem found.” If you have a problem with
your SmartCast
®
, use the following troubleshooting guide
before calling the Customer Resource Center or sending
your unit in for repair.
1. The SmartCast
®
loses signal.
If the SmartCast
®
is not able to get
an RF signal from the RSS™, the
display will stop updating (the
screen will freeze) and the RF35
SmartCast
®
screen will be
displayed after several seconds.
Whenever reception is lost or the
RSS™ emerges from the water for more than a few
seconds, the RF35 SmartCast
®
screen will be
displayed until the RSS™ is placed back in the water
and reception is regained.
• The SmartCast
®
system is a line-of-sight wireless
product. If objects are placed between the RSS™
and the Wrist Mounted Display, the reception may
be lost.
• The RF35 depth range is 2 to 120 feet (0.6 to 35
meters). Erratic readings may occur in water that is
shallower than 2 feet (0.6 m). In addition, because of
the nature of sonar, this product is not intended for use
in swimming pools or small enclosed bodies of water.
• Reeling the RSS™ too fast can cause loss of signal
and the screen will freeze.
• Check the buoyant balance between the RSS™
and your tackle; over 0.2 ounce (5.7 grams) will
submerge the RSS™, causing signal loss.
• The RF35 may not obtain its maximum RF distance
of 75 feet (22 meters) unless the water is smooth.
Waves or chop may reduce the RF range
significantly.
NOTE:Retrieving the RSS™ too rapidly,or the repetitive rocking
motion of rough water, can result in loss or distortion of the
bottom detail on the display. For best bottom detail, perform a
smooth and slow reel-in with constant speed and the rod tip up
(holding the rod tip low or using a heavy line may cause the
RSS™ to submerge and momentarily lose radio contact). The
RSS™ has a maximum transmit range of 75 feet (22 meters).
If the unit is cast or drifts more than 75 feet (22 meters) away
from the receiver, the signal may be inconsistent or lost.
2. Nothing happens when I turn the Wrist Mounted
Display on.
Check the battery position and make sure that the
battery door is properly closed. Also,make sure that
you have removed the plastic strip that is in the
battery compartment when it is new.
If this doesn’t help, replace the battery. After
replacing the battery, if the unit still doesn’t power
up, remove the battery door again and re-install.
3. When in very shallow water, I get gaps in the
bottom reading and inconsistent digital depth
indication.
The SmartCast
®
will work reliably in water 2 feet (0.6
meter) or deeper. The depth is measured from the
RSS™.
4. The display begins to fade out. Images are not as
sharp as normal.
Check the battery position and make sure that the
battery door is properly closed. Also,make sure that
you have removed the plastic strip that is located in
the battery compartment when it is new.
If this doesn’t help, replace the battery. After
replacing the battery, if the unit still has a faded
display, remove the battery door again and re-install.
5. The display shows many black dots at high
sensitivity settings.
You are seeing noise or interference caused by one
of several sources. Noise can be caused by other
electronic devices. Turn off any nearby electronics
and see if the problem goes away. Other sonar
devices or any electronic device operating in the 900
mHz range (in the 400 mHz range for International
versions) could cause interference with your
SmartCast
®
.
6. The display shows fluctuating depth readings and
excessive clutter, including vertical bars that may
be drawn on top of fish icons.
The SmartCast
®
system comes with the capability to
receive separate signals from a Channel A RSS™ or
a Channel B RSS™. Two A- or B-type RSS™ units
used simultaneously, as well as one A- and one B-
type RSS™ unit used simultaneously, can cause RF
interference between each other.
7. The display jumps and the bottom has an abrupt
change; sometimes a vertical line is missing or
a black line from top to bottom is displayed.
This display image jump is due to an automatic
change in depth. New returns graphed at a different
scale will not match up with the historic data already
graphed at a higher or lower scale.Vertical lines can
also occur as the radio signal from the
RSS™is lost
and then regained in rough water conditions.
Humminbird
®
6 Month Limited Warranty
We warrant the original retail purchaser that products
made by Humminbird
®
have been manufactured free from
defects in materials and workmanship. This warranty is
effective for 6 months from the date of original retail
purchase. Humminbird
®
products found to be defective
and covered by this warranty will be replaced or repaired
free of charge at Humminbird
®
option and returned to the
customer freight prepaid. Humminbird
®
sole responsibility
under this warranty is limited to the repair or replacement
of a product that has been deemed defective by
Humminbird
®
. Humminbird
®
is not responsible for charges
connected with the removal of such product or
reinstallation of replaced or repaired parts.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended
in the product installation and operation instructions;
• Damaged or has failed because of an accident or
abnormal operation;
• Repaired or modified by entities other than
Humminbird
®
.
Please retain your original receipt as a proof of the
purchase date. This will be required for in-warranty
service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER
WARRANTIES, OBLIGATIONS OR LIABILITIES ON THE
PART OF HUMMINBIRD
®
AND WILL BE THE CUSTOMER'S
EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE
HEREBY LIMITED IN DURATION TO SIX MONTHS FROM
THE DATE OF ORIGINAL PURCHASE. IN NO EVENT WILL
HUMMINBIRD
®
BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY RELATING TO THE
PRODUCTS.
International Purchases
A separate warranty is provided by international
distributors for units purchased outside the United States.
This warranty is included by your local distributor and this
distributor maintains local service for your unit. Warranties
are only valid in the area of intended distribution. Units
purchased in the United States or Canada must be
returned to our factory in the United States for service.
Humminbird
®
Service Policy
Even though you'll probably never need to take advantage
of our incredible service policy, it's good to know that we
back our products this confidently. We do it because you
deserve the best. We will make every effort to repair your
unit within three business days from the receipt of your
unit at our factory. This does not include shipping time to
and from our factory. Units received on Friday are typically
shipped by the following Wednesday, units received
Monday are typically shipped by Thursday, etc.
All repair work is performed by factory-trained technicians
to meet exacting factory specifications. Factory-serviced
units go through the same rigorous testing and quality
control inspections as new production units.
After the original warranty period, a standard flat rate
service charge will be assessed for each repair (physical
damage and missing parts are not included). Any repairs
made after the original warranty will be warranted for an
additional 90 days after service has been performed by
our factory technicians. You can contact our Customer
Resource Center or visit our website to verify the flat rate
repair fee for your product (visit the Product Support
section):
http://www.humminbird.com
We reserve the right to deem any product unserviceable
when replacement parts are no longer available or
impossible to obtain. This Service Policy is valid in the
United States only. This applies only to Humminbird
®
products returned to our factory in Eufaula,Alabama. This
Service Policy is subject to change without notice.
Returning Your Unit for Service
Before sending your unit in for repair, please contact the
factory, either by phone or by email, to obtain a Repair
Authorization Number for your unit. Please have your
product model name and serial number available before
calling the factory. If you contact the factory by e-mail,
please include your product model name and serial
number in the e-mail, and use Request for Repair
Authorization Number for your e-mail subject header. You
should include your Repair Authorization Number in all
subsequent communications about your unit.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the
Humminbird
®
Customer Resource Center.
• Tag product with your customer name, street address,
phone number and your assigned Repair Authorization
Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date
of purchase).
• Return product freight prepaid to Humminbird
®
, using
an insured carrier with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the
Humminbird
®
Customer Resource Center.
• Include payment in the form of credit card number and
expiration date, money order or personal check.
Please do not send cash.
• Tag product with your customer name, street address,
phone number and your assigned Repair Authorization
Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird
®
, using
an insured carrier with delivery confirmation.
If sonar performance becomes weak (i.e., there
are bottom gaps or "0" depth readings) the bottom
of the RSS™ needs to be cleaned with a drop or
two of a 5 to 10 percent solution of liquid dish-
washing detergent and water. Use approximately
one tablespoon (15 ml) detergent to 8 ounces (237
ml) of water to remove oils from the face of the
RSS™, then wipe with a damp cloth.
Temperature of 50 Means Channel
is Set to A
Temperature of 55 Means Channel
is Set to B
Temperature of 40
Means LED is OFF
Temperature Setting of 45
Means LED is On
SPECIFICATIONS
Wrist Mounted Display Specifications:
Power Requirement ................................One 2450 CR Battery
Display Matrix ....................................................48 X 32 Pixels
Display Type
.............................................................. STN
RSS
TM
Specifications:
Power Requirement ..................................One non-replaceable
Lithium RSS
TM
Battery
Battery Expected Life......................................................3 years
(approximately 500 hours of in-water use)
Depth Capability ........................ 2 - 120 feet (0.6 - 35 meters)
Sonar Coverage ................................................ 90° @-10 dB*
Sonar Operating Frequency ........................................ 125 kHz
Operational Radio Frequency .................................. 916.5 mHz
(433.92 mHz International)
Operational Range...................................... 75 feet (22 meters)
Contact Humminbird
®
Your Humminbird
®
accessory is designed for
trouble-free operation and is backed by a
six-month warranty.
If you have any questions, contact our
Humminbird
®
Customer Resource Center:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
custserv@johnsonoutdoors.com
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
* Area of bottom coverage equals twice the current depth.
Humminbird
®
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference and;
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Humminbird
®
could void
the user’s authority to operate the device.
FCC ID: ICLSMC1