Ingersoll-Rand 3-1/4 and 4 BORES Marine Safety Devices User Manual


  Open as PDF
of 8
 
     
CYLINDER 1-1/2” BORE 2” BORE 2-1/2” BORE 3-1/4” BORE 4” BORE
TYPE HEAD CAP HEAD CAP HEAD CAP HEAD CAP HEAD CAP
NON-CUSHIONED 119462 119471 119480 119489 119498 119507 119516 119525 119534 119543
CUSHIONED 119651 119666 119654 119669 119657 119672 119660 119675 119663 119678
NON-CUSHIONED MS4 119464 119473 119482 119491 119500 119509 119518 119527 119536 119545
CUSHIONED MS4 119652 119667 119655 119670 119658 119673 119661 119676 119664 119679
NON-CUSHIONED TRUNNION 119901 119902 119903 119904 119905 119906 119907 119908 119909 119910
CUSHIONED TRUNNION 119653 119668 119656 119671 119659 119674 119662 119677 119665 119680
    119752 119754 119756 119758 119760 119762 119764 119766 119768 119770
CUSHIONED FEM. RET. BOLT 114063 114064 114065 114066 114067 114068 114069 114070 114071 114072
     119835 119836 119839 119840 119843 119844 119847 119848 119851 119852
     119877 119878 119879 119880 119881 119882 119883 119884 119885 119886
BORE
SIZE
SPACER “A” “B” CAP SCREW g TORQUE
(FT LBS)
1-1/2” 119577-150 .375” 2.000” 1/4” - 28 x 2-1/4” 9
2” 119577-200 .375” 2.500” 5/16” - 24 x 2-1/4” (Low Head) 16
2-1/2” 119577-250 .375” 3.000” 5/16” - 24 x 2-1/4” (Low Head) 21
3-1/4” 119577-325 .625” 3.750” 3/8” - 24 x 2-3/4” 35
4” 119577-400 .625” 4.500” 3/8” - 24 x 2-3/4” 49
Q When used with MF1 flange, spacer 119577-( ) is mounted between head and flange and requires 4 mounting screws of
the size listed in the table.
Q When used without MF1 flange, spacer 119577-( ) is slid over piston rod and bushing, against cylinder head. No new mount-
ing screws are required. Spacer is attached using Loctite or “superglue”.
CYLINDER TYPE
A - Double Acting, Single Rod End
B - Double Acting, Double Rod End
RKN
X X
X X B
PROVENAIR SEAL KITS
BORE SIZE
Q - 1-1/2” 5 - 5”
S - 2” 6 - 6”
T - 2-1/2” 8 - 8”
W - 3-1/4” Y - 10”
4- 4”
ROD DIAMETER
K - 5/8” Q - 1-3/4”
M - 1” S - 2”
P - 1-3/8”
SEALS
B - Nitrile; Nitrile, Mag
S - Self-Lube; Self-Lube, Mag
V - Viton; Viton, Mag
NOTE: All seal kits include wear strip and cushion seals.
HEADS AND CAPS
CUSHIONED BOTH ENDS
119577-( ) SPACER INSTALLATION
To replace tie rod cylinders that have end caps made from castings (such as Wabco, Taiyo and Aro series 38 / 39), use
spacers as called out below.
“A”
“B”
“B”
Q Spacer
Mounting Screw for MF1 mount (4 req’d) g
MF1 Head Flange
Cylinder Head
g Not Supplied
 previous