Filter
Top Products
PF20X-X-X-BPage 6 of 8
PARTS LIST / PF20X-X-X-B AIR SECTION
n Indicates parts included in 637421 Air Section Service Kit shown below and items (70), (144), (175), (180) shown on page 4.
AIR MOTOR PARTS
Item Description (size) Qty Part No. [Mtl] Item Description (size) Qty Part No. [Mtl]
101 Center Body (PF20A-X-X-B) (1) 94028 [A]
(PF20S-X-X-B) (1) 94109 [SS]
103 Bushing (1) 94092 [D]
105 Screw (M6x1-6gx20mm) (4) 95887 [SS]
111 Spool (1) 95651 [D]
118 Actuator Pin (0.250”x 2.276” long) (2) 94083 [SS]
121 Sleeve (2) 94084 [D]
~ 127 90 St. Elbow (1-1/2 -11-1/2 N.P.T.) (1) 94860 [C / I]
128 Set Screw (1/4” -20 x 1/4”) (2) Y29-42-S [SS]
n 132 Gasket (1) 94099 [B]
133 Lockwasher (1/4”) (PF20A-X-X-B) (3) Y1 17-416-C [C]
(PF20S-X-X-B) (3) Y14- 416-T [SS]
134 Screw (M6x1-6gx30mm) (4) 96358 [SS]
135 Valve Housing (PF20A-X-X-B) (1) 96334-1 [A]
(PF20S-X-X-B) (1) 96337-1 [SS]
136 Plug (PF20A-X-X-B) (1) 96335 [A]
(PF20S-X-X-B) (1) 96339 [SS]
n 137 “O” Ring (1/16” x 2”o.d.) (1) Y325-32 [B]
n 138 “U” Cup (3/16”x 1.792” o.d.) (1) 95966 [B]
n 139 “U” Cup (3/16” x 1-1/4”o.d.) (1) Y186-50 [B]
140 Valve Insert (1) 95650 [Ck]
141 Valve Plate (1) 95659 [Ck]
n 146 “O” Ring D (3/32” x 1-1/16”o.d.) (1) Y325-118 [B]
n 147 “O” Ring D (1/8” x 1/2”o.d.) (2) Y325-202 [B]
n 166 Track Gasket z (1) 94026 [B]
n 167 Pilot Piston (includes168 and 169) (1) 67164 [D]
168 “O” R ing (3/32”x 5/8” o.d.) (2) 94433 [U]
169 “U” C up (1/8” x 7/8”o.d.) (1) Y240-9 [B]
170 Piston Sleeve (1) 94081 [Br]
n 171 “O” Ring (3/32” x 1-1/8” o.d.) (1) Y325-119 [B]
n 172 “O” Ring (1/16” x 1-1/8” o.d.) (1) Y325-22 [B]
n 173 “O” Ring (1/16” x 1-3/8” o.d.) (2) Y325-26 [B]
Kn 174 “O” Ring (1/8”x 1/2” o.d.) (2) Y325-202 [B]
n 176 Diaphragm (checkvalve) (2) 94102 [SP]
n 199 Track Gasket (1) 95666 [B]
n 200 Gasket (1) 95665 [B]
~ 201 Muffler (1) 94810
233 Adapter Plate (PF20A-X-X-B) (1) 96336 [A]
(PF20S-X-X-B) (1) 96338 [SS]
240 Screw (M6x1-6gx16mm) (2) 95991 [SS]
n 241 Track Gasket (1) 96344 [B]
n 242 “O” Ring (1/16”x 7/32” o.d.) (1) Y325-5 [B]
n 243 “O” Ring (1/8”x 5/8” o.d.) (1) Y325-204 [B]
n 244 “O” Ring (1/8”x 7/8” o.d.) (1) Y325-208 [B]
Ln Lubriplate FML-2 Grease (1) 94276
Lubriplate Grease Packets (10) 637308
D Used on models PF20S-XXX-SXX-B only.
z Used on models PF20A-XXX-SXX-B only.
~ Items not shown
K Fluid Section Kit parts, see page 4.
AIR MOTOR SECTION SERVICE
Service is divided into two parts - 1. Pilot Valve, 2. Major Valve.
GENERAL REASSEMBLY NOTES:
S Air Motor Section Service is continued from Fluid Section repair.
S Inspect and replace oldparts with new parts as necessary. Look for
deep scratches on metallic surfaces, and nicks or cuts in “O” rings.
S Take precautions to prevent cutting “O” rings upon installation.
S Lubricate “O” rings with Lubriplate FML-2 grease.
S Do not over-tightenfasteners, refer to torque specification block on
view.
S Re-torque fasteners following restart.
S SERVICE TOOLS -- To aid in the installation of (168) “O” rings onto
the (167) pilot piston, use tool # 204130-T, available from ARO.
PILOT VALVE DISASSEMBLY
1. A light tap on (118) should expose the opposite (121) sleeve, (167)
pilot piston and other parts.
2. Remove (170) sleeve, inspect inner bore of sleeve for damage.
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Install new (171 and 172) “O” rings, replace (170) sleeve.
3. Installnew (168)“O” ringsand (169)seal -Note thelip direction.Lu-
bricate and replace (167).
4. Reassemble remaining parts, replace (173 and 174) “O” rings.
MAJOR VALVE DISASSEMBLY
1. Remove (135) valve block and (233) adapter plate, exposing (166
and 132) gaskets and (176) checks.
2. Remove (233) adapter plate, releasing (140) valve insert, (141)
valveplate,(199,200and241)gasketsand(243and244) “O”rings.
3. Remove (136) plug and (137) “O” ring, releasing (111) spool.
MAJOR VALVE REASSEMBLY
1. Install new (138 and 139) “U” cups on (111) spool -- LIPS MUST
FACE EACH OTHER.
2. Insert (111) spool into (135) valve housing.
3. Install (137 and 242) “O” rings on (136) plug and assemble plug to
(135) valve housing, securing with (105) screws.
4. Install (140) valve insert, (141) valve plate, (199) gasket and (243
and244) “O”rings into(135) valvehousing. NOTE:Assemble (140)
valve insert with “dished” side toward (141) valve plate. Assemble
(141) valve plate with part number identification toward (140) valve
insert.
5. Assemble (200 and 241) gaskets and (233) adapter plate to (135)
valve housing, securing with (240) screws.
6. Assemble (132 and 166) gaskets and (176) checks to (101) center
body.
7. Assemble (135) valve housing and components to (101) center
body, securing with (134) screws.
(en)