26 SYSTEM CONFIGURATION
System Configuration
When the adjustment has been made, or if no
adjustment is required and all settings on this
page are complete, press the
⁄
/
¤
Navigation
Button
E
F until the on-screen cursor is
pointing to
PAGE1 and then press the
Set Button
F
Q to return to the main
IN/OUTSETUP menu to configure another
input, or if no further input configuration adjust-
ments are needed, press the
⁄
/
¤
Navigation
Button
E
F until the on-screen cursor is
pointing to
MASTERMENU and then press
the Set Button
F
Q to return to the main
menu screen.
Video Monitor Settings
The VIDEOMONITOR SETTINGS
menu (Figure 10) is unique in that it contains a
mix of information display lines that detail status
information about the AVR 645’s video system
settings, along with a few lines where a specific
parameter may be changed.With the
MASTER
MENU
on the screen, press the
⁄
/
¤
Navigation Button
E
F until the on-
screen cursor is pointing to
VIDEO
MONITORSETTINGS
and then press the
Set Button
F
Q to move to the menu
screen.
Figure 10
The IN VIDEOFORMATline is an informa-
tional display of the resolution of the incoming
video stream, and may not be adjusted.
The
INVIDEO COPYPROTline is an
informational display that shows whether or not
an incoming video signal contains copy
protection encoding, and may not be adjusted.
The
VIDEOPROCESS line is an informa-
tional display of the setting made in the
IN/OUTSETUP menu indicating how
incoming video is processed for the input being
viewed, and may not be adjusted.
The
COMPONENTOUTline is an informa-
tional display of whether or not the Component
Video outputs are
ENABLEDor OFF, based
on the input signal type and resolution, and
whether or not the incoming video signal has
HDCP content protection. It may not be adjusted.
The
S-VIDEOOUT line is an informational
display of whether or not the S-video outputs are
available at a 576i resolution (or OFF), based on
the input signal type and resolution and whether
or not the incoming video signal has HDCP
content protection. It may not be adjusted.
The
DISPLAYINTER line allows you to
choose between an
ANALOGvideo output
default value and an HDMI/DVI output by press-
ing the
‹
/
›
Navigation Button
E
F to
make the desired selection.When the setting is
ANALOG, the HDMI output is placed in a
Standby mode so that it automatically switches
to HDMI when an HDMI signal is detected. If a
high-definition input source is not HDCP-content-
protected, it may be output through the compo-
nent jacks; otherwise, it will be sent only to the
HDMI outputs.The
HDMI/DVIsetting routes
all converted or processed video to the HDMI
outputs.
The HDMIAUDIO OUT line allows you to
choose whether a two-channel downmix of the
audio that accompanies the selected source is
sent over the HDMI connection (
YES) at the
maximum bit rate the display’s audio system is
capable of handling, or not (
NO). To change the
setting, press the
‹
/
›
Navigation Button
E
F to make the desired selection.
When required adjustments have been made for
this input, or if no adjustment is required, press
the
⁄
/
¤
Navigation Button
E
F until
the on-screen cursor is pointing to
BACKTO
MASTERMENU
and then press Set Button
F
Q to return to the main menu screen.
Audio Setup
This menu allows you to configure the tone con-
trols. If you do not wish to change any of those
settings at this time, proceed to the next menu
screen. However, to make configuration changes
to those parameters, make certain that the
MASTERMENUis on the screen with the ➞
cursor pointing to the
AUDIOSETUP line,
and press the Set Button
F
Q.The
AUDIOSETUPmenu (Figure 12) will appear.
Figure 12
The first line controls whether or not the
bass/treble tone controls are in the signal path.
The normal default is for them to be in-line, but if
you wish to remove them from the circuit for
“flat” response, first make certain that the ➞
cursor is pointing to the
TONEline on the
menu and press the
‹
/
›
Navigation Button
E
F so that OUTis highlighted in reverse
video.
If you wish to leave the tone controls in the sig-
nal path, the amount off boost or cut for bass
and treble may be adjusted by pressing the
⁄
/
¤
Navigation Button
E
F so that the
➞ cursor is next to the line for the setting you
wish to adjust. Next, press the
‹
/
›
Navigation
Button
E
F until the desired setting is
shown.
When all desired changes have been made on
this menu, press the
⁄
/
¤
Navigation Button
E
F so that the ➞ cursor is next to the
BACKTOMAIN MENUline and press
the Set Button
F
Q.
* AUDIO SETUP *
TONE :IN OUT
BASS :0
TREBLE :0
BACK TO MASTER MENU
→
*VIDEO MONITOR SETTINGS*
IN VIDEO FORMAT: 1080i
IN VIDEO COPY PROT: ON
VIDEO PROCESS: V CONVERS
COMPONENT OUT: OFF
S-VIDEO OUT: OFF
COMPOSITE OUT: OFF
DISPLAY INTER: HDMI/DVI
HDMI AUDIO OUT: NO
BACK TO MASTER MENU
→
29851_AVR645_ENG 30/10/06 9:46 Side 26
