To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with maximum power of more than 50 W (both at the rear and
at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change <Amplifier Gain> setting to prevent the speakers from
being damaged (see page 18 of the INSTRUCTIONS).
• To prevent short circuits, cover the
terminals of the UNUSED leads with
insulating tape.
• The heat sink becomes very hot after use.
Be careful not to touch it when removing
this unit.
KW-AVX726/KW-AVX724/
KW-AVX626/KW-AVX624
Installation/Connection Manual
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
Main unit Power cord
Round head screws (M5 × 8 mm)
Flat head screws (M5 × 8 mm)
Crimp connector
Remote controller
Batteries
Plate for use with a Nissan car
160 91.3
100
30˚
Dashboard
20
4
INSTALLATION (IN-DASH MOUNTING)
1 Remove the audio system originally installed in the car, together with its mounting brackets.
Note: Be sure to keep all the screws and parts removed from your car for future use.
2 Attach the mounting brackets (removed from the car), to this unit (see below).
3 Do the required electrical connections.
• See pages 2 – 4.
4 Install this unit using the screws removed in step 1.
The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer.
If necessary, restore the protruding tabs.
Note : When installing the unit on the mounting bracket, make sure to use the supplied
screws (M5 × 8 mm). If longer screws are used, they could damage the unit.
When installing the unit in a Nissan car
Install the unit at an angle of less than 30˚, taking it into
account that the monitor would eject when in use.
Required space for installation and the
monitor ejection
Unit: mm
Supplied screws
Mounting bracket removed from the car
Screws removed from the car in step
1
Supplied screws
Select the appropriate
type fitting to your
audio system space.
Mounting bracket removed from the car
Plate for use with a Nissan car
GET0605-010A
[A/UI]
0109DTSMDTJEIN
EN
© 2009 Victor Company of Japan, Limited
Heat sink
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident.
• The driver must not watch the monitor while driving. It may lead to carelessness and cause an accident.
• If you need to operate the unit while driving, be sure to look around carefully or you may be involved in
a traffic accident.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback picture
will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake system built
in the car.
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding installation
kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used,
parts could become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
Install1_KW-AVX726_010A_f.indd 1Install1_KW-AVX726_010A_f.indd 1 12/23/08 12:33:01 PM12/23/08 12:33:01 PM
