Masterpage:Right-NoTitle0
EN
65
Filename [HDS1EU_4.fm]
Page 65 June 21, 2001 12:29 pm
L-2 SELECT Setting
Set “L-2 SELECT” to the appropriate mode depending on the
type of appliance connected to the recorder’s AV2 (L-2) IN/
DECODER connector.
A
Select the input mode for the AV2 (L-2) IN/
DECODER connector.
B
Return to the normal screen.
Press MENU.
NOTES:
● If you have a satellite receiver or a decoder connected to the
AV2 (L-2) IN/DECODER connector, be sure to set “L-2
SELECT” back to appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to
the AV2 (L-2) IN/DECODER connector, leave “L-2 SELECT” set
to “A/V”.
● The default setting is “A/V”; if the recorder’s memory backup
has expired due to a power cut or because the AC was
removed from the recorder, “A/V” will be automatically
selected when the power is restored to the recorder. If you are
using a satellite receiver or a decoder, be sure to set “L-2
SELECT” back to appropriate mode.
● When “L-2 SELECT” is set to “SAT”, “SAT” appears on TV
screen or front display panel instead of “L-2” or “L2”.
● If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set
“L-2 SELECT” to “DECODER”.
F-1 INPUT Setting
Set “F-1 INPUT” to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
A
Select the input mode for the VIDEO/S-
VIDEO connector.
B
Return to the normal screen.
Press MENU.
Perform steps
A
and
B
of “L-1 OUTPUT and L-1 INPUT
Setting” on page 64.
A Press
rt
to move the
arrow to “L-2 SELECT”,
then press OK.
B Press
rt
to select the
appropriate setting, then
press OK.
* The default setting is
bold
in
the table below.
8
L-2 SELECT
A/V
: To use this recorder as the recording
deck with the player connected to
the AV2 (L-2) IN/DECODER
connector, or to use the satellite
receiver connected to the AV2 (L-2)
IN/DECODER connector.
DECODER
: To use a decoder connected to the
AV2 (L-2) IN/DECODER connector.
SAT
: To view a satellite programme with
the TV set while the recorder is
turned off. (
੬
pg. 70)
HDD/VCR SET UP INITIAL SET UPFUNCTION SET UP
L-1 OUTPUT VIDEO
L-1 INPUT VIDEO
L-2 SELECT A/V
F-1 INPUT VIDEO
INPUT/OUTPUTFUNCTION
SELECT OK EXIT
THEN PRESS [OK]
INDEX MENU
SELECT WITH
A/V
DECODER
SAT
Perform steps
A
and
B
of “L-1 OUTPUT and L-1 INPUT
Setting” on page 64.
A Press
rt
to move the
arrow to “F-1 INPUT”,
then press OK.
B Press
rt
to select the
appropriate setting, then
press OK.
* The default setting is
bold
in
the table below.
8
F-1 INPUT
VIDEO
: When connecting an appliance to
the VIDEO input connector, set to
“VIDEO”.
S-VIDEO
: When connecting an appliance to
the S-VIDEO input connector, set to
“S-VIDEO”.
HDD/VCR SET UP INITIAL SET UPFUNCTION SET UP
L-1 OUTPUT VIDEO
L-1 INPUT VIDEO
L-2 SELECT A/V
F-1 INPUT VIDEO
INPUT/OUTPUTFUNCTION
SELECT OK EXIT
THEN PRESS [OK]
INDEX MENU
SELECT WITH
VIDEO
S-VIDEO
HDS1EU_.book Page 65 Thursday, June 21, 2001 12:30 PM
