46
BR-DV6000
PROFESSIONAL
MENU RESET
A.DUB
EJECT
COUNTER
AUDIO INPUT
SELECT
MONITOR OUTPUT REMOTE
LOCAL
CTL L
MIX
R
CH-1/2
MIX
CH-3/4
DV
LINE
Y/C
(CPN)
TC
UB
REW STOP FF
REC
OPERATE
PLAY PAUSE
DISP
SET SEARCH+
BLANK CUE UP
HOLD
PHONES REC LEVEL
CH-1/3 CH-2/4
MIC
SEARCH–
Mini
VIDEO
LINE
IN
OUT
MONITOR
OUT
DC12V
DV
IN/OUT
IN OUT
OFF
AUDIO
REMOTE2
IN
B-YR-Y
SYNC IN
TIME CODE
IN OUT
Y
COMPONENT
OUT
CH 1/3 CH 2/4
IN
OUT
MONITOR
OUT
REMOTE1
TIMER
REC PLAY
SERIAL
REMOTE
SIGNAL
GND
Y/C
SERIAL OUTSERIAL IN
———
REMOTE[ 1 / 2]
———
REMOTE SEL 9P ON
REMOTE SEL SER ON
REMOTE SEL DV ON
REMOTE SEL JVC ON
REMOTE SEL NET ON
LOCAL FUNCTION STP+EJT
PREROLL 7SEC
NEXT PAGE
P AGE BACK
———REMOTE[2/2]———
REM FF /REW MODE FF /REW
REM STOP SEL . EE
PB START DELAY OF
SYNCHRONI ZAT ION ON
CONTROLLER SEL TYPE1
FOOT SW OFF
PAGE BACK
:Connection:
The serial remote controller (RM-G30, sold separately) can be con-
nected to the SERIAL REMOTE IN terminal located on the rear panel
of BR-DV6000.
The input signals of the SERIAL REMOTE IN terminal can be through-
output from the SERIAL REMOTE OUT terminal. (Only with OPER-
ATE ON)
:Setting:
Ⅵ To use the SERIAL IN terminal, set REMOTE SEL SER
in the REMOTE (1/2) Menu screen to ON or LOC+REM.
Then, set the REMOTE/LOCAL switch on the front panel
accordingly.
● REMOTE SEL SER
ON : When the REMOTE/LOCAL switch is set to REMOTE,
operations can be performed via the SERIAL REMOTE
IN terminal.
LOC+REM: With the REMOTE/LOCAL switch is set either way,
operations can be performed via the SERIAL REMOTE
IN terminal. With this setting, the buttons and switches
of the unit can be used too.
Ⅵ Set FOOT SW in the REMOTE (2/2) Menu screen ac-
cording to how the serial remote terminal is used.
OFF : Set to OFF when the serial remote controller is used.
The footswitch cannot be used.
L EDGE : Recording and recording pause is switched at the LOW
edge of the footswitch signal.
H EDGE :Recording and recording pause is switched at the
HIGH edge of the footswitch signal.
L LEVEL : Recording is performed at the LOW edge and paused
at the HIGH edge of the footswitch signal.
:Operation:
Before using the foot switch, set BR-DV6000 to the RECORDING or
RECORDING PAUSE mode using the relevant buttons of the unit.
(Only with L EDGE and H EDGE)
Memo
● The foot switch can only be used to switch between RECORDING
ON and OFF.
● The foot switch can be operated regardless of the setting of the
REMOTE/LOCAL switch.
Memo
● Besides recording, the
serial remote controller
can perform other func-
tions.
● If the REMOTE SEL SER
is set to ON, unit buttons
that can be operated can
be selected from LOCAL
FUNCTION in the RE-
MOTE (1/2) Menu
screen.
Recording can be turned ON/OFF with a serial remote controller or foot switch connected to the
SERIAL REMOTE IN terminal located at the rear panel of BR-DV6000.
REMOTE/LOCAL switch
• Serial remote controller: RM-G30
•Foot switch
REMOTE (1/2) Menu screen
REMOTE (2/2) Menu screen
RECORDING – Recording with serial remote terminals –
Foot switch
Serial IN
H
400ms
L
Min
Signal
terminal
DV6000U_28-051_Eng.p65e 03/04/03, 3:07 PM46
