Before you stat-t...
Check location where washer will
be installed. Proper installation is
your responsibility. ‘“-I-- -“--
Untape and open washer lid. Remove
packages and hoses from washer.
II
II
\,m, I l.n...-. n\.nF..lk;nr
yuu , lavG Gvcl yll ,,, Ig necessary
for correct installation.
Hot and cold water faucets: Must be
within 4 feet of the back of the washer
and provide water pressure 5-l 00 PSI.
Laundry tub drain system: Needs a
20-gallon laundry tub. Top of tub must
be at least 34 inches
high and no
Grounded electrical outlet is
required. See Electrical
requirements.
Standpipe drain system: Needs
a two-inch minimum diameter
standpipe with minimum
carry-away
capacity of
17 gallons per
minute. Top of
standpipe must ti
be at least 34
inches high and
no higher than
F-f----
72 inches from
bottom of
washer.
I
drain
hose
I
i
(Part No. 388423) and
hose extension kit (Part No.
285442) are available from
authorized parts distributors. If
drain hose must be shortened,
Floor drain
/
system requires a
siphon break, Part
Important: Observe all governing
codes and ordinances.
er heater:
Set
water to washer.
SEE
INS1
‘RUCTIONS ON
Support: Entire floor must be sturdy enough
support washer weight of 315 pounds.
BACK COVER.
Tools needed for
installation:
scissors
Parts supplied for
installation:
Remove parts from packages. Check that
all parts were included.
1 small clamp
literature package
1 drain hose
1 hose clamp
2 inlet hoses
4 flat water hose
washers
2 front leveling legs
with nuts
. Level floor:
under entire
Sctrical
equirements
Electrical Shock Hazard
l Electrical ground is required on
this appliance.
l If cold water pipe is interrupted by
plastic, non-metallic gaskets or
other insulating materials, Do Not
use for grounding.
. Do Not ground to a gas pipe.
l Do Not modify the power supply
cord plug. If it does not fit the
outlet, have a proper outlet
installed by a qualified electrician.
l Do Not have a fuse in the neutral
or grounding circuit. A fuse in the
neutral or grounding circuit could
result in an electrical shock.
l Do Not use an extension cord with
this appliance.
l Check with a qualified electrician
if you are in doubt as to whether
the appliance is properly
grounded.
Failure to follow these instructions
could result in serious injury or
death.
codes.permit and a separate
rounding wire is used, it is
tcommended that a qualified
lectrician determine that the
rounding path is adequate.
ZO-volt, 60-Hz, AC-only, 15 or 20-
mpere fused electrical supply is
squired. (Time-delay fuse or circuit
reaker is recommended.) It is
?commended that a separate circuit
erving only this appliance be provided.
Maximum
washer-l
slope
inch.
Product Damage
Do Not store or operate
washer below 32°F (some
water may remain in
washer).
See Use & Care Guide for
“Winterizing” Information.
Failure to follow above may
result in product damage.
Recommended
grounding method
For your personal safety, this appliance
must be grounded. This appliance is
equipped with a power supply cord
having a 3-prong grounding plug. To
minimize possible shock hazard, the cord
must be plugged into a mating 3-prong
grounding-type wall receptacle, grounded
in accordance with National Electrical
Code, ANSVNFPA 70-latest edition and
all local codes and ordinances. See
Figure 1. If a mating wall receptacle is
not available, it is the personal
responsibility and obligation of the
customer to have a properly grounded 3-
prong wall receptacle installed by a
qualified electrician.
3-prong
grounding
Plug j
3-prong
grounding-
type wall
receptacle
supply cord
Figure 1
Panel A
