RE-ASSIGNING DEVICE KEYS
The Millennium 4 can be set up to control a second TV or VCR, or any combination of four home entertainment components. For
example, to have the Millennium 4 control a TV, a Cable Converter, and two VCRs, you will need to re-assign the unused AUDIO
key to operate the second VCR as follows:
1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 2. The LED will blink twice.
3. Press VCR once, then press AUDIO once.
4. The AUDIO key is now ready to be programmed for your second VCR. See Programming VCR/DVD Player Control on page 6.
To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the following chart for
a desired component:
To Re-Assign Perform Key Sequence
TV as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - TV
TV as 2nd Audio key: SETUP - 9 - 9 - 2 - AUDIO - TV
TV as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - TV
TV back to TV: SETUP - 9 - 9 - 2 - TV - TV
VCR as 2nd TV key: SETUP - 9 - 9 - 2 - TV - VCR
VCR as 2nd Audio key: SETUP - 9 - 9
- 2 - AUDIO - VCR
VCR as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - VCR
VCR back to VCR: SETUP - 9 - 9 - 2 - VCR - VCR
AUDIO as 2nd TV key: SETUP - 9 - 9 - 2 - TV - AUDIO
AUDIO as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - AUDIO
AUDIO as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - AUDIO
AUDIO back to AUDIO: SETUP - 9 - 9 - 2 - AUDIO - AUDIO
Upon completion of a re-assignment, the LED will blink twice to confirm your selection. At that time, you will also need to program
the Millennium 4 to control the new component. See previous sections on Programming TV Control, Programming VCR/DVD Player
Control, Programming Cable Converter (or DBS Receiver) Control, or Programming Audio Control.
CHANGING VOLUME LOCK
The Millennium 4 is set to control volume of a component through your TV while in the TV, VCR, or Cable mode. However, in the
Audio mode, you have separate control of your audio component’s volume. If your TV is not remote controllable, or if you would like
the volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-
associated mode (e.g., through the cable in the TV mode).
To Change Volume Lock to the Cable Mode:
1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press CBL once. The LED will blink twice.
3. Now, whenever you press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your cable converter or DBS
receiver.
To Change Volume Lock to the TV Mode:
1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press TV once. The LED will blink twice.
3. Now, whenever you press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your TV.
To Change Volume Lock to the VCR Mode:
1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press VCR once. The LED will blink twice.
3. Now, whenever you press VOL+, VOL-, or MUTE on the remote, volume will be controlled by your VCR or DVD player.
To Change Volume Lock to the Audio Mode:
NOTE: Performing these steps will allow you to access the volume control of your audio component in all modes.
1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press AUDIO once. The LED will blink twice.
3. Now, whenever you press VOL+, VOL-, or MUTE on the remote, volume will be controlled by your audio component.
Page 14 of 15
