Hayward Pools HAYWARD POOL SYSTEM CONTROL Marine Sanitation System User Manual


  Open as PDF
of 7
 
6
BASIC PROGRAMMING OF MASTER CONTROL PANEL (continued)
TO PROGRAM POOL AND SPA SET TEMPERATURE:
1. Push Program button, display will blank out with the exception of the “SET” icon.
2. Push Heater button and display will show current desired set temperature of spa.
Display will show “SET TEMPERATURE OF SPA.” Set temperature may be
adjusted with the Up and Down buttons. Range is 70°F - 104°F (21°C - 40°C).
3. Push Program again and display will show current desired set temperature of pool. Display will show “SET
TEMPERATURE OF POOL..” Set temperature may be adjusted with the Up and Down buttons.
Range is 50°F - 95°F (10°C - 35°C).
4. Push Program again to display heating mode. Push Up or Down to select desired heating mode.
Push Program to exit. The available heating modes are: A) Gas, B) Solar, C) Gas and Solar. Solar heating is
only available when an optional valve actuator is installed (see plumbing schematics).
NOTE: See Note on previous page (under “to program time of day”) for instructions on selecting °Celsius or °Fahrenheit.
TO PROGRAM AUXILIARY 1:
1. Push the Program button, display will blank out with the exception of the “SET” icon.
2. Push the Aux 1 button and display will show current Aux 1 (POOL FEATURE) operation
in hours along with the icons “SET # OF HOURS TO RUN POOL FEATURE 1.” Duration
may be adjusted with the use of the Up and Down buttons. Range is 0 to 24 hours.
3. Push Program again to program time of day and to start automatic Aux 1 cycle.
Display will show “SET TIME OF DAY TO START POOL FEATURE 1.” Aux 1 cycle start time may be adjusted by
the Up and Down buttons in 30-minute increments. Push Program to exit.
TO PROGRAM AUXILIARY 2:
1. Push the Program button, display will blank out with the exception of the “SET” icon.
2. Push the Aux 2 button and display will show current Aux 2 operation in hours
along with the icons “SET # OF HOURS TO RUN POOL FEATURE 2.” Duration
may be adjusted with the use of the Up and Down buttons. Range is 0 to 12 hours.
3. Push Program again to program time of day and to start automatic Aux 2 cycle. Display will show “SET TIME OF
DAY TO START POOL FEATURE 2.” Aux 2 cycle start time may be adjusted by the Up and Down buttons in 30-
minute increments. Push Program to exit.
TO PROGRAM AUXILIARY 3
1. Push the Program button, display will blank out with the exception of the “SET” icon.
2. Push Aux 3 button and display will show current Aux 3 (POOL FEATURE) operation in
hours along with the icons “SET # OF HOURS TO RUN POOL FEATURE 3.” Duration
may be adjusted with the use of the Up and Down buttons. Range is 0 to 12 hours.
3. Push Program again to program time of day and to start automatic Aux 3 cycle.
Display will show “SET TIME OF DAY TO START POOL FEATURE 3.” Aux 3 cycle start time may be adjusted by
the Up and Down buttons in 30-minute increments. Push Program to exit.
TO PROGRAM AUXILIARY 4
1. Push Program button, display will blank out with the exception of the “SET” icon.
2. Push Aux 4 button and display will show current Aux 4 operation in hours along
with the icons “SET # OF HOURS TO RUN POOL FEATURE 4.” Duration may be
adjusted with the use of the Up and Down buttons. Range is 0 to 12 hours. Push
Program again to program time of day and to start automatic Aux 4 cycle. Display
will show “SET TIME OF DAY TO START POOL FEATURE 4.” Aux 4 cycle start time may be adjusted by the Up
and Down buttons in 30-minute increments. Push Program to choose the F.O. Light or the On/Off Light option.
Display will show either “Fo” or “Lt.” Choose mode by pressing Up or Down. Push Program to exit. Aux 4 option
will not operate during programmed times.
3. To choose between On/Off Light and the F.O. (fiber-optic) feature for Aux 4, push the program button once,
followed by Aux 4. Press Program two more times after that. With the Up and Down arrows, you can toggle
between “FO” and “LT.” Press Program to set and exit. “FO” allows you to access: light, light option on, light
option off, light off. “Lt” allows you to turn the underwater light on and off.
TO PROGRAM AUXILIARY 5
1. Push the Program button, display will blank out with the exception of the “SET” icon.
2. Push the Aux 5 button and display will show current Aux 5 (Aux 5 on expander
board) operation in hours along with the icons “SET # OF HOURS TO RUN
POOL FEATURE 5.” Duration may be adjusted with the use of the Up and Down
buttons. Range is 0 to 24 hours.
3. Push Program again to program time of day and to start automatic Aux 5 cycle. Display will show “SET TIME OF
DAY TO START POOL FEATURE 5.” Aux 5 cycle start time may be adjusted by the Up and Down buttons in 30-
minute increments. Push Program to exit.
 previous