Ingersoll-Rand 612041-X Marine Sanitation System User Manual


 
CCN 99444598
OPERATOR’S MANUAL 612041-X
RELEASED: 10-23-86
REVISED: 10-12-11
(REV
. K)
2” AIR MOTOR
1:1 RATIO
0 - 150 P.S.I. RANGE
INCLUDE MANUAL: S-632 GENERAL INFORMATION (PN 97999-624)
INCLUDING: SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, PARTS, TROUBLESHOOTING
2” DIFFERENTIAL
TRANSFER PUMP
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
612042-X
SERVICE KITS
Use only genuine AROR replacement parts to assure compatible
pressure rating and longest service life.
637084 for air motor repair (see page 2).
637081 for lower pump end (Nitrile) repair (see page 3).
637083 for lower pump end (PTFE) repair (see page 3).
SPECIFICATIONS
Model Series 61204X-X.................
Type Air Operated, transfer pump.......................
Ratio 1:1.......................
Air Motor Diameter 2’’ (5.08 cm)............
Stroke 6’’ (15.24 cm)....................
Air Inlet (female) 1/4 - 18 N.P.T.F. - 1.............
Material Inlet immersed...............
Material Outlet (female) 3/4 - 14 N.P.T.F. - 1.......
Pump Construction Carbon Steel..........
Dimensional Data See Chart.............
Weight See Chart......................
PERFORMANCE
Air Inlet Pressure Range 0 - 150 p.s.i. (0 - 10.3 bar)........
Fluid Pressure Range 0 - 150 p.s.i. (0 - 10.3 bar)..........
Maximum Rec’d Cycles / Minute 75..
Displacement In
3
Per Cycle 18.8......
Volume / Cycle 10.4 oz. (307.7 ml)................
Cycles Per Gallon 12.3.............
Maximum Working Flow Rate 9 g.p.m. (34.1 l.p.m.)....
Maximum Flow Rate 18 g.p.m. (68.1 l.p.m.)...........
Noise Level @ 60 p.s.i., 40 c.p.m. 77.8 db(A)*..
* Thepumpsound pressure level hasbeenupdatedto anEquivalentContinuousSound
Level (L
Aeq
) to meetthe intentof ANSI S1.13-1971, CAGI-PNEUROP S5.1 usingfour
microphone locations.
GENERAL DESCRIPTION
The Aro 2’’ differential 1:1 ratio transfer pumps are intended to be used
primarily for oil transfer and delivery systems. It is best to use this pump
with low - medium viscosity fluids. It uses carbon steel and other materi-
als which make it compatible with most petroleum based lubrication
products.
OPERATING AND SAFETY PRECAUTIONS
WARNING
Read the General Information Manual for operat-
ing and safety precautions and important information.
PUMP DATA
Figure 1
Material Inlet
Immersed
Air Inlet (female)
1/4 - 18 N.P.T.F. - 1
MODEL 61204X-X
Material Outlet (female)
3/4 - 14 N.P.T.F. - 1
NOTE: Dimensions are shown in inches and (mm), supplied for reference only and are typically
rounded up to the nearest 1/16 inch.
MODEL “A” (mm) “B” (mm) WEIGHT (kg)
612041-X 54” (1371.6) 34-5/8” (879.5) 13 lb (5.9)
612042-X 64-1/4” (1631.9) 44-7/8” (1139.8) 14 lb (6.4)
“A”
‘‘B’’
48
IMPORT
ANT
This is one of two documents which support the pump. Replace-
ment copies of these forms are available upon request.
= 612041-X MODEL OPERATOR’S MANUAL
- S-63
2
GENERAL INFORMATION LUBRICATION PISTON PUMPS
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
© 2011
www.ingersollrandproducts.com