Filter
Top Products
Av. Kit Install. Manual
190-00067-02 Rev. J
Page 14
Non- GARMIN part numbers shown are not maintained by GARMIN and
consequently are subject to change without notice.
NOTE: Alternate contacts for 18 AWG wire: As an alternate to the Positronic
contacts listed (and provided in the install kit), the installer may use contacts
made by ITT Cannon as follows: Socket contact - ITT Cannon p/n: 031-10007-
001, Pin contact - ITT Cannon p/n: 330-5291-055. These contacts require the
use of a different crimp tool positioner than that shown in the table, with part
numbers as follows: Daniels p/n: K250, Astro p/n: 616245, or ITT Cannon p/
n: 980-00005-722.
See Appendix B for information regarding obsolete stamped type contacts.
3.4 RACK INSTALLATION
A. Figure 3-4 shows outline dimensions for the aviation rack. Install the rack in
a rectangular 6.320" x 2.000" hole in the instrument panel. Exercise caution
when installing the rack into the instrument panel. The rack is designed to
facilitate removal of the GNC 300 for portable use. Deformation of the rack may
make it difficult to install and remove the GNC 300.
B. Install the rack in the aircraft panel using four #6-32 countersunk screws and
four self-locking nuts or other FAA approved methods as per Advisory Circular
43.13-1A. The screws are inserted from the inside through the holes in the sides
of the rack (see Figure 3-5).
Contacts
Standard Density Connectors Hi Dens. Connector
37 socket connector (J1 on unit) 9 pin connector (on battery pack) 26 pin connector (J2 on unit)
20-24 AWG socket contact 18 AWG socket contact 20-24 AWG pin contact 18 AWG pin contact 22-28 AWG pin contact
Garmin p/n 336-00022-00 336-00023-00 336-00024-00 336-00025-00 336-00021-00
military p/n M39029/63-368 n/a M39029/64-369 n/a M39029/58-360
Amp 205090-1 n/a 205089-1 n/a 204370-2
Positronic M39029/63-368 FC6018D M39029/64-369 MC6018D M39029/58-360
ITT Cannon 031-1007-042 see note 330-5291-037 see note 030-2042-000
Tools
Hand Standard Density Connectors (size 20 contacts) Hi Dens. Connector (size 22D)
Crimping pin or socket contacts (20-24 AWG) pin or socket contacts (18 AWG) pin contacts (22-28 AWG)
Tool positioner insert/extract positioner insert/extract positioner insert/extract
military p/n M22520/2-01 M22520/2-08 M81969/1-02 n/a M81969/1-02 M22520/2-09 M81969/1-04
Positronic 9507 9502-5 M81969/1-02 9502-11 M81969/1-02 9502-3 M81969/1-04
ITT Cannon 995-0001-584 995-0001-604 980-2000-426* see note 274-7048-000* 995-0001-739 n/a
Amp 601966-1 601966-5 91067-2 n/a n/a 601966-6 91067-1
Daniels AFM8 K13-1 M24308/1-02 K774 M24308/1-02 K42 M24308/18-1
Astro 615717 615725 M81969/1-02 see note M81969/1-02 615724 M81969/1-04
* Insert/extract tools from ITT Cannon are all plastic, others are plastic with metal tip.