Icom EX-2714 Fish Finder User Manual


 
12
4
BASIC OPERATION
TRAILS function
The trails function memorizes echoes continuously or
at constant intervals. This is useful for watching other
shipstracks, approx. relative speed, etc.
Setting the trail interval time
q Push [MENU]/[ ] twice to call up the VIDEO
menu.
Push [Ú] several times until the TRAIL TIME section
becomes highlighted.
w Push [Ω ≈] to select trail interval time.
6 sec., 15 sec., 30 sec., 1 min., 3 min., 6 min., 15 min.
and (continuous) are available.
e Push [MENU] several times to exit the menu.
Using the TRAILS function
q Push [TRAILS]/[ ] to turn the trail function
ON.
•“TRAILS and trail interval time appears in the upper
right of the screen.
Trail interval counter starts to count up to the trail time.
w All displayed echoes at the plotted time are memo-
rized and displayed with a graduated intensity to-
gether with the current echoes.
Echoes are displayed with minimum intensity when
is selected.
e Push [TRAILS]/[ ] to cancel the trail function
and erase the plotted echoes.
•“TRAILS and trail interval time disappears.
Trail time
3/4
(0.25)
M.TUNE
1:05
NM
CURS
STW 15.7KT
H UP
011.4˚R
HDG 253.9˚T
6M
TRAILS
IR
ES
T.VECT
0.453NM
TRAIL
indicator
Trail interval
counter
Trail time
Power save function
The power save function conserves the boats battery
power by pausing the transmission. The standby
(pausing) times are selectable (rotation number is xed
to 10).
For example, when 1 min. is selected, the scanner ro-
tates 10 revolutions; then stops for 1 min., and then re-
peats this sequence while the power save function is
activated.
DSetting the scanning standby time
q Push [MENU]/[ ] four times to call up the INT.
SETTING menu.
w Push [Ú] until the SAVE TIME section becomes
highlighted.
e Push [Ω ≈] to select standby time.
1, 6, 15, and 30 min. are available.
r Push [MENU]/[ ] twice to exit the menu display.
DUsing the power save function
q Push and hold [TX (SAVE)]/[ ] for 1 sec. to
turn the power save function ON.
The save indicator appears in the top of the screen.
w After the scanning rotations are nished, transmis-
sion and rotation are suspended until the selected
standby time elapses.
The display shows the last scanned echoes until the
scanning restarts.
•“SAVE and standby time appear in the top of the screen
and the standby time is counted down.
e After the selected standby time elapses, transmis-
sion and rotation restart.
r Push [TX (SAVE)]/[ ] to cancel the power
save function.
The save indicator turns OFF.
NOTE: When you use the power save function to-
gether with the alarm function, the CRT display is
turned OFF until an object enters the programmed
alarm zone, therefore, more power saving is possi-
ble. (p. 17)
CURS 34˚ 37.72N CURS 34˚ 37.72N
1
(0.25)
T.VECT 6M
0.900NM
NM
CURS
SOG17.7KT
H UP
014.6˚T
HDG273.9˚T
IR
ES
EBL1
EBL2
MOB
VRM1
VRM2
135˚ 34.42E
0:48
SAVE
Push and hold [TX] for 1 sec.
to turn the SAVE function on.
Scan and STBY alternates
Count down the standby time
1
(0.25)
T.VECT 6M
0.900NM
NM
CURS
SOG17.7KT
H UP
014.6˚T
HDG273.9˚T
IR
ES
EBL1
EBL2
MOB
VRM1
VRM2
135˚ 34.42E
0:00
SAVE
COMPASS
GPS
COMPASS
GPS
MR-1000R2_T2.qxd 04.2.24 10:22 Page 12