Kenwood TS-480SAT Marine Radio User Manual


 
52
11 MEMORY FEATURES
Memory Scroll
1 Press [QMI/ M.IN] (1 s) to enter Memory Scroll
mode.
The memory channel that was last selected
appears.
2 Turn the MULTI control, or press Mic [UP]/
[DWN] to step through the memory channels.
•You can also change channels by entering a
2-digit number. Press [8], [9] for example.
3 To exit Memory Scroll mode, press
[MTR/ CLR].
The transceiver re-displays the memory
channel or VFO frequency that was
selected before you activated Memory
Scroll.
Note:
While the transceiver is in Memory Scroll mode, you can
operate the following controls and keys only:
[QMI/ M.IN]
,
[MTR/ CLR]
, numeric keys (
[0]
~
[9]
), Mic
[UP]
/
[DWN]
,
Mic
[PTT]
,
AF
control,
SQL
control,
MULTI
control and
[ ]
(POWER).
Do not press
[QMI/ M.IN]
again after entering Memory Scroll
mode. Pressing
[QMI/ M.IN]
results in over-writing the
current VFO data to the memory channel you selected.
Temporary Frequency Changes
After retrieving frequencies and associated data in
Memory Recall mode, you can temporarily change
the data without overwriting the contents of the
memory channel.
1 Access Menu No. 07 and select “on”.
Skip this step when changing only the
associated data (not the frequency).
2 Recall a memory channel.
3 Change the frequencies and associated data.
Use only the Tuning control to select a
frequency.
4 If necessary for future use, store the changed
data in another memory channel. Refer to
“Channel Channel Transfer” {below}.
Note:
If Menu No. 07 is selected “on”, the frequency of the split-
memory channel can be changed while using the TF-SET
function.
MEMORY TRANSFER
Memory \ VFO Transfer
After retrieving frequencies and associated data
from Memory Recall mode, you can copy the data
to the VFO. This function is useful, for example,
when the frequency you want to monitor is near
the frequency stored in a memory channel.
1 Recall the desired memory channel {page 51}.
2 Press [QMR/ M
ss
ss
sVFO] (1 s).
When a simplex channel is recalled, the
data is copied to VFO A or VFO B,
depending on which VFO was used to recall
the channel.
When a split channel is recalled, the RX
data is copied to VFO A and the TX data is
copied to VFO B.
Note:
Pressing
[QMR/ M
ss
ss
s
VFO] (1 s)
after temporarily changing
the retrieved data copies the new data to the VFO.
Channel \ Channel Transfer
You can also copy channel information from one
memory channel to another. This function is
useful when storing frequencies and associated
data that you temporarily change in Memory
Recall mode.
1 Recall the desired memory channel {page 51}.
2 Press [QMI/ M.IN] to enter Memory Scroll
mode.
•To exit Memory Scroll mode, press
[MTR/ CLR].
3 Select the memory channel where you would
like the data copied, using the MULTI control.
4 Press [QMI/ M.IN] (1 s).
98~00lennahC a 98~00lennahC
ycneuqerfXR
a
ycneuqerfXR
ycneuqerfXT
a
ycneuqerfXT
XRrofedoM
a
XRrofedoM
XTrofedoM
a
XTrofedoM
petsycneuqerfXR
a
petsycneuqerfXR
petsycneuqerfXT
a
petsycneuqerfXT
ycneuqerfenoT
a
ycneuqerfenoT
ycneuqerfSSCTC
a
ycneuqerfSSCTC
SSCTC/enoT
sutatsFFO/NO
a
SSCTC/enoT
sutatsFFO/NO
emaNyromeM
a
emaNyromeM
lennahCyromeM
FFO/NOtuokcoL
a
lennahCyromeM
FFOtuokcoL