Kenwood TS-480SAT Marine Radio User Manual


 
70
13 OPERATOR CONVENIENCES
VOICE GUIDE
When the optional VGS-1 is installed, each time you
change the transceiver mode such as VFO A/ B or
Memory Recall, the transceiver automatically
announces the new mode. In addition, you can
program the Remote Control panel [PF] key so that
pressing it makes the transceiver announce the
displayed information. If you have the optional
MC-47 microphone with MJ-88 plug adaptor, you
can program one of the Mic [PF] keys for this
function as well.
The table below indicates what the transceiver
automatically announces when it changes the settings.
desserPyeK noitarepO tnemecnuonnA
]B/A[
AOFV
S
1
+B/A+
ycneuqerF
BOFV
][,][ egnahcdnaBycneuqerF
]V/M/B/A[
)s1(
roOFV
yromeM
llaceR
S+OFV
1
++B/A
ycneuqerF
ro
yromeM+lennahC
roycneuqerF+.oN
knalb
/UNEM[
]KCOL.F
.oNuneM
noitceles
+.oN+uneM
+rebmundetceleS
retemaraP
][,][
uneM
retemaraP
egnahc
retemarapdetceleS
]NI.M/IMQ[
)s1(
yromeM
edomllorcS
+niyromeM
.oNyromeM+
ycneuqerF
]TNE[
ycneuqerF
yrtne
retnE
ITLUM
lortnoc
.oNuneM
segnahc
detceleS+.oN
+rebmun
retemaraP
yromeM
.oNlennahc
segnahc
lennahcyromeM
ycneuqerF+.oN
rofsgnitteS
suoirav
snoitcnuf
eulavretemaraP
yekciremuN
yrtne
gniretnE
srebmun
rebmunyrevE
deretne
yeknoitcnuF
agnitceleS
noitcnuf
+emannoitcnuF
retemaraP
kcoL.qerF
noitcnuf
ycneuqerF
sutatskcol
/NOkcolycneuqerF
FFO
kciuQ
yromeM
llacer
kciuQllaceR
yromeM
+yromemkciuQ
+rebmunyromeM
S
1
+B/A+
ycneuqerF
1
“S” is anounced when the transceiver is operating in Split-
frequency mode.
2
The PF key assignment parameter is announced as the number
shown below.
rebmununeM161ECIOV262ECIOV36INOMXR
46
XRPSD
INOM
56
.QERF
KCOL
66)TTP(DNES76ENUTXT
86BSLBSU96KSFWC07MAMF17TES-FT
27RMQ37IMQ47TILPS57B/A
67V/M77B=A87NACS97V>M
08NI.M18T.WC281HC382HC
483HC58ENIF68.RLC78RTM
88zHM982/1TNA09BN19RN
29CB39LND99FFO
For the [PF] key, the transceiver will announce
different information, depending on whether VOICE1
or VOICE2 is selected.
VOICE1:
The frequency on display, channel number,
various mode settings, and Menu settings are
announced.
The frequency for the VFO or memory channel will
be announced to 10 Hz digit. For the MHz
decimal point, “point” is announced. If the
memory channel has no data stored, “blank” is
announced.
If a memory channel that has no data is selected
in Memory Scroll mode, “blank” is announced.
Note:
If operating a key or a control changes the contents of the
display while an announcement is in progress, the announcement is
interrupted.
VOICE2:
The S-meter readings at the time you pressed the
key, are announced, for example, “S5” or “20 dB”.
The table below shows the available announcements
when the [PF] (VOICE2) is pressed.
reteM-S
leveL
-ecnuonnA
tnem
reteM-S
leveL
-ecnuonnA
tnem
00S018S
3~11S119S
42S21Bd01
53S41~31Bd02
64S51Bd03
75S71~61Bd04
86S81Bd05
97S02~91Bd06
1 Assign VOICE1 (61) or VOICE2 (62) to the
Remote Control panel [PF] key by accessing
Menu No. 48. Or, if you are using the optional
MC-47 microphone, assign one of the Mic [PF]
keys to either VOICE1 or VOICE2. For
programming Mic [PF] keys, refer to
“MICROPHONE PF KEYS” {page 64}.
2 Press the [PF] key that you programmed.
An announcement is made based on the
VOICE1 or VOICE2 selection.
•To interrupt the announcement, press the [PF]
key again.