Oceanic 04-8792-49 Scuba Diving Equipment User Manual


 
13
OCi OPERATING MANUAL
© 2002 Design, 2013 Doc. No. 12-5335-r01 (6/27/13)
CDT (Countdown Timer) SETUP, information includes (Fig. 6A/B):
> Graphics CDT SETUP solid with OFF (or ON) flashing and SET solid.
> Remaining Countdown Time (hr:min) if ON and a countdown is in progress, or 0:00 if ON and no time is remaining, or
0:00 or the time previously set if OFF.
• A (< 2 sec) - to step forward through the selections OFF, ON, and SET.
• S (2 sec) - to revert to the Watch Main Menu.
If OFF or ON is flashing, S (< 2 sec) will save the selection and revert to the Watch Main Menu.
ON does not start the countdown, start/stop is controlled while viewing the Watch ALT screen.
If SET is flashing, S (< 2 sec) will access Set CDT.
Once the CDT has been set and turned ON (ready to start, but not started), it will be displayed on the Watch ALT screen
where it can be started, stopped, or reset until set OFF. When the countdown reaches 0:00, the Audible will sound (10 sec)
during which 0:00 and CDT will be displayed on the Watch Main Time screen in place of Dual Time and Day of Week.
Upon entering any Dive Computer mode, Watch CDT operation will be terminated and the countdown time will revert to the
hr:min value previously set.
Set CDT, information includes (Fig. 7):
> Graphics CDT SETUP, solid.
> Graphics OFF, ON, and SET solid.
> Time (hr:min), Hour digits flashing.
• A (hold) - to scroll upward through the Hour set points at 8/second from 0: to 23: in 1 hour (1:) increments.
• A (< 2 sec) - to step up through the set points one at a time.
• M (< 2 sec) - to step back through the set points one at a time.
• S (< 2 sec) - to save the Hour setting and flash the Minute digits.
• A (hold) - to scroll upward through the Minutes set points at 8/second from :00 to :59 in 1 minute (:01) increments.
• A (< 2 sec) - to step up through the set points one at a time.
• M (< 2 sec) - to step back through the set points one at a time.
• S (< 2 sec) - to save the hour:minute set point, with SET flashing allowing OFF or ON to be selected (see Setup above).
• S (2 sec) - to revert to the Watch Main Menu.
FREE Mode has a separate (min:sec) CDT.
CHRONOGRAPH (Stop Watch/Lap Timer), information includes (Fig. 8A/B):
> Graphic LAP1 (or 2 up to 9) if previously started or blank if not yet started
> Graphic CHRONO.
> Elapsed time if previously started, or 0:00:00.00 (hr:min:sec_ .01 sec) if not yet started, flashing.
• S (upon press) - to display the graphic LAP1 and start the Chrono (run time) which will begin counting up from 0:00:00.00
to 9:59:59.99 hr:min:sec_ .01sec in increments of .01 (1/100th sec). After the first 4.99 seconds, the .01 sec digits will
be displayed as 2 dashes ( . - - ).
• S (upon press) - to save Lap 1’s time and display the graphic LAP2 with the Timer continuing to count up.
Total Run Time is
always displayed until the Chrono is stopped.
• S (upon press) - to freeze Lap Times (1 up to 9). After 9, subsequent Laps will be recorded and the earliest Lap discarded.
Freezing of a Lap Time is prevented when S is operated during an Alarm strike.
If the Chrono continues to run and reaches 9:59:59.99, it will stop and record that as a Lap. Subsequent presses of S then
have no effect.
• A (< 2 sec) - to stop the Chrono and recall Lap 1 displaying the graphic LAP1 and the Lap time. Subsequent presses of A
will recall the other Laps.
• A (2 sec) - to stop the Chrono if running, and reset it to 0:00:00.00.
• M (2 sec) - to revert to Watch Main with Chrono running in the background.
Once the Chrono has been set and started, it will remain on display (or continue to run in the background) while on the
surface until reset by the user. Upon descending to 5 FT/1.5 M (i.e., entry into Dive Mode), operation will be terminated
and the counter will reset to 0:00:00.00 (hr:min:sec.xx).
DAILY ALARM
When set On, the Daily Alarm, that runs in the background, will sound the Audible at the time set every day. The Audible will
not sound while operating in dive computer modes.
Daily Alarm Status, information includes (Fig. 9):
> Graphics DAILY ALARM solid, with OFF (or ON) flashing.
> Alarm Time (hr:min) last set, with graphic AM (or PM) if 12 Hour Format.
• A (< 2 sec) - to step forward (down) through the selections OFF, ON, and SET.
• M (< 2 sec) - to step back (up) through the selections.
• S (< 2 sec) - to save the selection that is flashing.
Fig. 8A - CHRONO
(started, running)
Fig. 8B - CHRONO
(started, frozen or recalled)
Fig. 9 - DAILY ALARM
STATUS (upon access)
Fig. 6A - CDT SETUP
(Off, not yet set)
Fig. 6B - CDT SETUP
(On, running)
Fig. 7 - SET CDT
(hour then minutes)