Filter
Top Products
13
TK-760G/762G
9. Channel Setting Mode
Each channel can be setup in its action mode by using
the panel keys.
• Pressing [MON] when "SELF" is diaplyed, sets channel
setting mode.
• Select an item set using [
] then change the selection
with the [CH
/ ].
• The data displayed using [D/A] is stored in the memory
and then proceeds to the next item.
• Pressing [
] proceeds to the next item without storing it
in the memory.
• Press [MON] to set the display to "SELF" and return to
reset (default) status.
The setup items fro channel setting mode are listed be-
low.
No. Function
Choices Display Remarks
Select 1~128 __1-__1._ [ ] : Group selection/
channel __1-128._ Channel selection
Select 1~128 __1.-__1_ change
group 128.-__1_
1 RX Step STP__250 Display when an item
frequency
2.5kHz~1MHz STP_1000 is selected or when a
step is changed
(about 0.5 seconds)
[A] : Step change
2.5, 5.0, 6.25, 7.5kHz,
1MHz step
Blank - - - - - - - - [ ] : Frequency on/
100.0000~ R.100.0000 blank switching
550.0000MHz The rightmost dot
indicates 50Hz digit
(On=5, Off=0)
2 RX Off - - - - - - - - [ ] : Off/QT/DQT
signalling
QT 67.0~250.3Hz
QT__67.0_ switching
(EIA mode) QT_250.3_ [A] : Mode switching
QT 67.0~250.3Hz
QT__67.0* [SCN] : Normal/
(0.1Hz step mode)
QT_250.3* Inverse switching
DQT 000~777 DQT000N*
(Normal) DQT777N*
(1 step mode)
DQT 023~754 DQT023N_
(Normal) DQT754N_
(Standard table mode)
DQT 000~777 DQT000I*
(Inverse) DQT777I*
(1 step mode)
DQT 023~754 DQT023I_
(Inverse) DQT754I_
(Standard table mode)
REALIGNMENT
IC502
TX-RX unit B/2
Foil side
50
51
IC505
1
8
4
5
D507
D505
Fig. 3
Note :
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
[D/A]
[D/A]
[ ]
[D/A]
[MON]
[CH
/ ]
Radio type
Channel set
mode
Function set
mode
Self programming mode
Portable
Mobile
Radio band &
channel type
VHF
8CH
VHF
128CH
UHF
8CH
UHF
128CH
Frequency
version
[CH / ]
[CH
/ ]
[CH
/ ]
[CH
/ ]
VHF
F1
VHF
F2
UHF
F1
UHF
F3
[CH / ]
[CH
/ ]
[CH
/ ]
[CH
/ ]
UHF
F4
[CH
/ ]
[ ]
Cannot be
set when
portable is
select.
Cannot be
set when
mobile is
select.
*
**
*
8-2. Model Select Mode
• Flow chart
Note :
If the radio type of TK-760G was temporally set to "Por-
table" for the cloning purposes, "UNPROG" is displayed (at
User mode) when the TK-760G is turned on.
In this case, please set the radio type back to "Mobile" at
model select mode menu.
The silk screen of D505 and D507 is reversed on the TX-
RX unit PCB (Part No. J72-0677-
02). this silk screen will be
corrected from the next version, J72-0677-
12.