Filter
Top Products
MOUNTING
Install the X-55A in
any
convenient
location,
provided
there is clearance
behind the unit when
it is tilted for the best
viewing angle.
Holes in the
bracket base allow wood
screw or
through-bolt
mounting.
You
may
need
to
place
a
piece
of
plywood
on the back of thin
fiberglass panels
to secure
the
mounting
hardware.
Make certain there is
enough
room behind the unit
to attach the
power
and
transducer cables.
The smallest hole that will
pass
one
power
ortransducer
plug
is 5/8". After
the hole is
drilled,
pass
the transducer connector
up through
the hole
first,
then
pass
the
power
cable down
through
it.
After
routing
the
cables,
fill the hole with a
good
marine
sealing compound.
Offsetthe
bracketto coverthe hole.
Routethe
powercablethrough
the slot
and breakoutone of the
otherslots in the bracket
forthe transducer cable.
POWER CONNECTIONS
The X-55A works from a
twelve-volt
battery system.
For the best
results,
attach the
power
cable
directly
to the
battery.
You can attach
the
power
cable to an
accessory
or
power buss,
however
you may
have
problems
with electrical interference.
Therefore,
it's saferto
go
ahead and
attach the
power
cable
directly
to the
battery.
If the cable is not
long
enough, splice
#18
gauge
wire onto it. The
power
cable hastwo
wires,
red and
black. Red
is the
positive
lead,
black is
negative
or
ground.
Make certain to
attach the
in-line
fuse holderto the red lead as
close to the
powersource
as
possible.
For
example,
if
you
have to extend
the
power
cable to the
battery
or
power
buss,
attach one end of
thefuse
holderdirectlyto
the
batteryorpower
buss.
This will
protect
both the unit and
the
power
cable in the
event of a short.
The X-55A uses a
3-amp
fuse.
IMPORTANT!
Do not use this
product
without a
3-amp
fuse wired into the
power
cable!
Failure to use a
3-amp
fuse will void
your warranty.
2
51
How
to Obtain
Service
(Canadian
Customers
Only)
We back
your
investment in
quality products
with
quick, expert
service and
genuine
Lowrance
replacement parts.
If
you
need service or
repairs,
contact the Lowrance
Factory
Customer Service
Department
at the
toll-tree number listed below. A
technician
may
be able to solve the
problem
and save
you
the inconvenience
of
returning your
unit.
You
will be asked for
your
units
serial number.
800-347-1014
Canada
Only. Monday through Friday
8:00 A.M.
-
8:00 P.M. central
Time,
How to Obtain
Service
(International
Customers
Only)
If
you
need service or
repairs,
contact the dealer in the
country you purchased your
unit.
WARRANTY
REPAIR WILL BE HONORED ONLY IN THE
COUNTRY
UNIT WAS
PURCHASED.
Please follow the
shipping
instructions shown below on this
page
if
you
have to mail
your
unitto the dealer. For
propertesting, repair,
and
service,
send a brief
note with the
product
describing
the
problem.
Be sure to include
your name,
return
shipping
address,
and a
daytime telephone
number.
Shipping
Information
When
sending
a
product
for
repair, please
do the
following:
1.
Always
use
the
original shipping
container and filler
material the
product
was
packed
in when
shipping your product.
2
Always
insure the
parcel against
damage
or loss
during shipment.
Lowrance does not
assume
responsiblity
for
goods
lost or
damaged
in transit
3.
For
propertesting, repair,
and
service,
send a brief note with the
product describing
the
problem.
Be sure
to include
your
name, return
shipping address,
and a
daytime
telephone
number.
Accessory Ordering
Information
To order accessories such
as
power
cables or
transducers, please
contact:
1. Your
local marine dealer. Most
quality
dealers that handle marine electronic
equipment
should be able to
assist
you
with these items.
consultyour
local
telephone
directory
for
listings.
2.
canadian customers
only
can write:
Lowrance/Eagle canada,
919 Matheson
Blvd.,
E.
Mississauga,
Ontario L4W2R7
or fax
416-629-3118
PDF compression, OCR, web-optimization with CVISION's PdfCompressor