Filter
Top Products
2.
Slip
the transducer's
mounting pad
between the bracket's
mounting
"ears". Sandwich two internal lock washers between the transducer and
one side of the
mounting
bracket as shown below. Place one washer on
the other side of the transducer.
11111
INSTALLATION
-
Transom
Mount
1. The transducer
must be
placed
in a location that has a smooth
flow of
water at all times. Air bubbles created
by
the movement of the
boat
hull
against
the water interfere with the sonar
signal.
This causes "noise" or
random
marks to
appear
on the sonar's
display.
You
may
need to
carefully
view the water's
path
at the transom while the
boat is
moving
to
determine the best location for the transducer.
2. Make certain the chosen location doesn't interfere
with the boat's
trailer. Mount the transducer at least
one foot from the
engine's
lower
unit. This will
prevent
air bubbles from the transducer
interfering
with the
propeller.
LOWRANCE ELECTRONICS
FULL ONE-YEAR
WARRANTY
'We", "our",
or "us" refers to LOWRANCE
ELECTRONICS. INC.,
the manufacturer
of this
product.
"You" or
"your"
refers to the first
person
who
purchases
this
product
as a consumer
item for
personal, family,
or household use.
We warrant this
product against
defects or malfunctions
in materials and
workmanship,
and
against
failure to conform to this
product's
written
specifications,
all for one
year (1)
from
the
date of
original purchase by you.
WE MAKE NO
OTHER EXPRESS WARRANTY OR
REPRESENTATION
OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT.
Your remedies under this
warranty
will be available so
long
as
you
can show in a reasonable
manner that
any
defect or malfunction in materials or
workmanship,
or
any
non-conformity
with the
product's
written
specifications,
occurred within one
year
from the date of
your
original purchase,
which must be substantiated
by
a dated sales
receipt
or sales
slip. Any
such
defect,
malfunction, or
non-conformity
which occurs within one
year
from
your original
purchase
date will either be
repaired
without
charge
or be
replaced
with a new
product
identical or
reasonably equivalentto
this
product,
atour
option,
within a reasonable time after
our
receipt
of the
product
If such
defect, malfunction,
or
non-conformity
remains
after a
reasonable number of
attempts
to
repair by us, you may
elect to obtain without
charge
a
replacementof
the
product
ora refund forthe
product.
THIS
REPAIR,
REPLACEMENT,
OR
REFUND
(AS
JUST
DESCRIBED)
IS THE EXCLUSIVE
REMEDY AVAILABLE TO YOU
AGAINST
US FOR ANY
DEFECT,
MALFUNCTION,
OR NONCONFORMITY CONCERN-
ING THE PRODUCT OR FOR ANY LOSS OR DAMAGE
RESULTING FROM ANY OTHER
CAUSE WHATSOEVER. WE
WILL NOT UNDER ANY CIRCUMSTANCES
BE LIABLE
TO
ANYONE FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL,
OR
OTHER INDI-
RECT DAMAGE OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental
or
consequential damages,
so the above limitations
or exclusions
may
not
apply
to
you.
This
warranty
does NOT
apply
in
the
following
circumstances:
(1)
when the
product
has
been serviced
or
repaired by anyone
other than
us,
(2)
when the
product
has been
connected,
installed, combined, altered,
adjusted,
or handled
in a manner other than
according
to the instructions fumished with the
product, (3)
when
any
serial number has
been
effaced, altered,
or
removed,
or
(4)
when
any
defect,
problem,
loss,
or
damage
has
resulted from
any
accident, misuse, negligence,
or carelessness,
or from
any
failure to
provide
reasonable and
necessary
maintenance in accordance with the instructions of the
owner's manual for the
product.
We reserve the
right
to make
changes
or
improvements
in our
products
from
time to time
without
incurring
the
obligation
to install such
improvements
or
changes
on
equipment
or
items
previously
manufactured.
This
warranty gives you specific legal rights
and
you may
also have other
rights
which
may
vary
from state to state.
REMINDER: You must retain the sales
slip
or sales
receipt proving
the date of
your original
purchase
in case
warranty
service is ever
required.
LOWRANCE ELECTRONICS
12000 E SKELLY DRIVE
TULSA,
OK
74128
(800)
324-1358
WASHER
WASHER
TWO WASHI
BOLT &
SLEEVE
3. Slide the metal sleeve over the bolt.
Slip
the bolt and sleeve
through
the
bracket, washers,
and transducer
assembly.
Place an internal tooth
lock washer over the end of the bolt and
thread the nut onto it. Do not
tighten
the nut at this time.
The
transducer
is now
ready
for installation.
BOLT
III 1111111111111111111111 I
6
47
PDF compression, OCR, web-optimization with CVISION's PdfCompressor