Filter
Top Products
8
Identify Restrictions/Permissions
Specify restrictions and permissions for each extension.
Line Access Restriction {#302} or
Pool Access Restriction {#315}
By default, access to all lines and pools is set to No Restriction. To change
the default, write the line numbers or pool access codes in the appropriate
columns, as follows:
Outgoing only – User can place outside calls and receive only
transferred calls on specified line or pool.
Incoming only – User cannot place outside calls but can receive calls
on specified line or pool.
No Access – User cannot place or receive outside calls on
specified line or pool (but can receive transferred
calls, pick up calls on hold, or join calls in Key mode
and on key extensions in Hybrid mode).
NOTE: Pool Access Restriction for key extensions in Hybrid mode is set to
No Access. Pooling and Hybrid mode are available only if you are using
PARTNER ACS R2.0 or later.
Outgoing Call Restriction {#401}
Write “IN” or “LOC” to indicate restrictions for all outgoing calls on all lines at
that extension, as follows:
IN – User can make only intercom calls to other system extensions.
LOC – User can make only intercom and local outside calls (no calls that
require a “0” or “1” prefix).
Any available outside lines can still be used to dial numbers on an Allowed
Phone Number List assigned to the extension, numbers on the Emergency
Phone Number List, or Marked System Speed Dial numbers.
Identify Group Assignments
To assign extensions to any of the following groups (each extension can be in
one or more groups), write the group number or place a check mark in the
appropriate columns.
Pickup Group Extensions {#501}
Any extension can answer an intercom, transferred, or outside call ringing at
an extension in the Pickup Group, without knowing which extension is ringing
and without being in the group. Do not put PARTNER MAIL, PARTNER MAIL
VS or PARTNER Voice Messaging extensions in a Pickup Group.
Calling Group Extensions {#502}
A user can ring or page (voice signal) all extensions in a Calling Group simul-
taneously or transfer a call by ringing the group. Once an extension answers, the
ringing or paging stops at the other extensions in the group. Do not assign
extensions connected to auxiliary equipment, PARTNER MAIL, PARTNER MAIL
VS, PARTNER Voice Messaging or External Hotlines to a Calling Group.
If a loudspeaker paging system is connected and Simultaneous Paging is
desired, put all desired system phones with speakers in Calling Group 1.
NOTE: When the user voice signals an extension that has a system phone,
the phone beeps and the user’s voice is heard through its built-in speaker.
System phones are the only ones that can be voice signaled.
Hunt Group Extensions 1–6 {#505}
Calls can ring or be transferred to the first non-busy extension in a Hunt
Group. A call rings at an extension in a Hunt Group three times; if it is not
answered, it hunts to the next non-busy extension, continuing until someone
answers or the caller hangs up. (If you voice signal a Hunt Group, only the
first extension is signaled; the call does not keep hunting if there is no
answer.) Incoming calls on specific lines can be directed to a Hunt Group
using Group Call Distribution {#206}. Do not put PARTNER MAIL or
PARTNER MAIL VS extensions in Hunt Groups 1–6.
VMS Only (Hunt Group 7)
For extension where PARTNER MAIL or PARTNER MAIL VS is connected,
check this box to assign the extension to Hunt Group 7. For PARTNER Voice
Messaging, virtual extensions 86 and 87 are automatically assigned to Hunt
Group 7 and no system programming is required (any previous assignments
for Hunt Group 7 are automatically erased). The system recognizes any
extensions assigned to Hunt Group 7 as Voice Mail Service (VMS—
PARTNER MAIL, PARTNER MAIL VS, or PARTNER Voice Messaging)
extensions. Do not assign any extensions other than VMS extensions to Hunt
Group 7. Also, do not assign PARTNER MAIL, PARTNER MAIL VS, or
PARTNER Voice Messaging extensions to any other Hunt Groups, to any
Calling or Pickup Groups, or to the Night Service Group.
Night Service Group Extensions {#504}
Check this box if the extension should be in the Night Service Group. When Night
Service is on, incoming calls on assigned lines or pools ring
immediately
at the
extensions in the Night Service Group, even if Line Ringing for those extensions is
set for “delayed ring” or “no ring.” Do not put PARTNER MAIL, PARTNER MAIL
VS or PARTNER Voice Messaging extensions in the Night Service Group.