Filter
Top Products
13
VTX OPERATING MANUAL
© 2002 Design, 2014 Doc. No. 12-5382-r01 (10/24/14)
SET AUTO DIM
TIME UNTIL DIM
OFF
DIM TO BRIGHTNESS
30 %
SET AUTO DIM
TIME UNTIL DIM
0:30 MIN:SEC
DIM TO BRIGHTNESS
30 %
SETUP MENU
SET DATE, TIME
BATT, TMT STATUS
BLUETOOTH
SET AUTO DIM
Fig. 15 - HOME SETUP
MENU
HOME SETUP MENU, selections include (Fig. 15):
> SET AUTO DIM - select to access the Set Auto Dim feature.
> SET DATE, TIME - select to access the Set Date, Time Menu.
> BATT, TMT STATUS - select to activate the VTX' receiver then view status information for the VTX and Transmitters.
> BLUETOOTH - select to initialize the Bluetooth function.
• A (< 2 sec) - to step forward (down) through the Menu selections.
• M (< 2 sec) - to step back (up) through the selections.
• S (< 2 sec) - to access the highlighted selection.
• S (2 sec) - to revert to the Home Menu.
SET AUTO DIM,
selections with the last settings saved include (Fig. 16A/B):
This feature will allow you to set a time that Dive Main screens will remain illuminated (after the last button press) at the Brightness
% level you adjusted it to before it is reduced to the Dim level that you set it to here.
> TIME UNTIL DIM with the graphic OFF, or 0:30 MIN:SEC, flashing.
> DIM TO BRIGHTNESS with 30 %.
• A (hold) - to scroll upward through Time set points 8/sec from OFF to 0:20 through 2:00 MIN:SEC in increments of 10
seconds (0:10).
• A (< 2 sec) - to step upward through the Time set points one at a time.
• M (< 2 sec) - to step back through the Time set points one at a time.
• S (< 2 sec) - to save the Time setting.
If OFF is selected, the Dim To Brightness setting is to be bypassed with operation reverting to the Home Setup Menu. The
Auto Dim feature is to be disabled and have no affect during dives.
If a min:sec Time value is saved, it is to become solid and Dim To Brightness % is to be highlighted and flash.
• S (2 sec) - to step back to the Setup Menu without saving the setting.
• A (< 2 sec) - to step upward through the % Dim set points from 10 through 60% in increments of 10% one at a time.
• M (< 2 sec) - to step back through the % set points one at a time.
• S (< 2 sec) - to save the setting,
which is to become solid with the highlight removed, and revert to the Home Setup Menu
with the Set Auto Dim selection highlighted allowing other operations
.
• S (2 sec) - to step back to Set Time without saving the setting.
SET DATE, TIME MENU, selections with the last settings saved include Fig. 17):
> DATE FORMAT = with M.D (for Month.Day) or D.M (for Day.Month).
> DATE = with Month.Day.Year or Day.Month.Year, based on the Date Format.
Set Year, then Month, then Day.
.
> HOUR FORMAT = with 12 (12: Am to 11: Pm) or 24 ( 0: to 23:).
> TIME = with hr:min (
12:01 A to 11:59 P, if 12 Hour Format; or 0:01 to 23:59, if 24 Hour Format).
Set Year, then Minute.
• A (< 2 sec) - to step forward (down) through selections.
• M (< 2 sec) - to step back (up) through selections.
• S (< 2 sec), when a selection is highlighted - to highlight and flash that item's set point (see below).
• A (< 2 sec) - to toggle or increase set points one at a time.
• A (hold) - to increase set points at a rate of 8 per second.
• M (< 2 sec) - to toggle or decrease set points one at a time.
• S (< 2 sec) - to save the setting which becomes solid, with the selection flashing.
• S (2 sec) - to revert to the Setup Menu.
BATTERY/TMT (TRANSMITTER) STATUS, information includes (Fig. 18):
Also refer to page 8.
> VTX = BATT GOOD (or LOW)
> TMT 1 = BATT GOOD (or LOW), or NOT AVAIL, or OFF
> TMT 2 = BATT GOOD (or LOW), or NOT AVAIL, or OFF
> TMT 3 = BATT GOOD (or LOW), or NOT AVAIL, or OFF
> TMT 4 = BATT GOOD (or LOW), or NOT AVAIL, or OFF
GOOD (green) means that battery power is acceptable (=> 2.75 volts).
LOW (yellow) means that the battery should be changed (< 2.75 volts, warning level).
LOW (red, flashing) means that the battery must be charged prior to further operations (< 2.50 volts, alarm level).
NOT AVAIL means that the VTX's receiver is not receiving that Transmitter's signal.
OFF means that the Transmitter has not been selected for use.
• S (2 sec) - to revert to the Setup Menu.
• 10 sec - revert to the Setup Menu if S is not pressed.
DATE FORMAT = M.D
HOUR FORMAT = 12
DATE = 7.24.14
SET DATE, TIME
TIME = 10:38 A
Fig. 17 - SET DATE, TIME
MENU
Fig. 18 - BATTERY/TMT
STATUS
BATT, TMT STATUS
VTX =
TMT
1 =
TMT 2 =
TMT 3 =
TMT
4 =
BATT GOOD
NOT AVAIL
BATT LOW
OFF
BATT GOOD
Fig. 16A - SET AUTO DIM
Fig. 16B - SET AUTO DIM