Filter
Top Products
48
6
SCANS
q If the start up screen is not selected (if [F-5]’s func-
tion is [EXIT]), push [F-5] one or more times to exit.
w Select VFO mode.
e Select the desired operating mode.
- The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
- See previous page for scan condition.
- If the [RF/SQL] control function is set as RF control, the
squelch always opens. See pgs. 2, 56 for details.
y Push [(F-1)PROG] to start the programmed scan.
- Decimal points blink while scanning.
u When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
i To cancel the scan, push [(F-1)
PROG].
NOTE: If the same frequencies are programmed
into the scan edge memory channel P1 and P2,
programmed scan does not start.
■ Programmed scan operation
2.4k2.4k9 2.8k2.8k455455
12:3412:34
ProgrammedP1:0.500.00MHz
ScanedgesP2:29.999.99MHz
∂FSpan:±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANFINEFINE EXITEXITPROGPROG
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
1ß
14.195.00
VFOVFO
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
2.4k2.4k9 2.8k2.8k455455
12:3412:34
ProgrammedP1:0.500.00MHz
ScanedgesP2:29.999.99MHz
∂FSpan:±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANFINEFINE EXITEXITPROGPROG
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
PROGRAM SCAN
1ß
14.195.00
VFOVFO
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
q If the start up screen is not selected (if [F-5]’s func-
tion is [EXIT]), push [F-5] one or more times to exit.
w Select VFO mode or a memory channel.
e Select the desired operating mode.
- The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
- See previous page for scan condition.
- If the [RF/SQL] control function is set as RF control, the
squelch always opens. See pgs. 2, 56 for details.
y Set the ∂F span by pushing [
(F-4)
∂FSPAN].
u Set center frequency of the ∂F span.
i Push [(F-2)∂F] to start the ∂F scan.
- Decimal points blink while scanning.
o When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
!0 To cancel the scan, push [
(F-2)
∂F].
■
∂∂
F scan operation
2.4k2.4k9 2.8k2.8k455455
12:3412:34
ProgrammedP1:0.500.00MHz
ScanedgesP2:29.999.99MHz
∂FSpan:±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANFINEFINE EXITEXITPROGPROG
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
1ß
14.195.00
VFOVFO
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
2.4k2.4k9 2.8k2.8k455455
12:3412:34
ProgrammedP1:0.500.00MHz
ScanedgesP2:29.999.99MHz
∂FSpan:±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANFINEFINE EXITEXITPROGPROG
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
∂FSCAN
1ß
14.195.00
VFOVFO
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO