Filter
Top Products
NB NR
BAL NR
COMP KEY SPEEDBK-IN DELAY
APF
APF
LOCKTX
RX
AUTO NOTCH
TWIN PBT
CW PITCH
F-1
SSB
F-2 F-3 F-4 F-5
SPEECH LOCK
RIT/ TX
TXRIT CLEAR
CW RTTY AM FM
SPLIT
MP-W MP-R
DUAL
WATCH
VFO/
MEMO
MAIN/
SUB
CHANGE
1.8
1
3.5
2
7
3
10
4
14
5
18
6
21
7
24.5
8
28
9
GENE
50
0
F-INP
ENT
MW
M-CL
TS
XFC
i756
1ß
VFOVFO
14.195.000
VFOVFO
USBUSB
USB
14.100.0014.100.00
14.205.00014.205.000
USBUSB
USB
14.100.0014.100.00
5656
ß
TXTX
FILTER SCANMEMORY SET
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
SCOPE
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
2.4k2.4k9 2.8k2.8k455455
12:3412:34
!8
@5@6@7@8@9
@1@0!9 @2 @3 @4
!8 MULTI-FUNCTION SWITCHES
•Push to select the functions indicated in the LCD
display to the right of these switches.
- Functions vary depending on the operating condition.
•Push to input a character for memory keyer pro-
gramming or memory name. (pgs. 36, 45)
•Toggles the antenna connector selection
between ANT1/R and ANT2/R when
pushed. (p. 37)
•Toggles the receive antenna ON and OFF
when pushed for 2 sec.
•Selects RF power (Po), SWR or ALC me-
tering during transmit. (p. 34)
•Selects one of 2 receive RF preamps or
bypasses them.
- “P.AMP1” activates 10 dB preamp for HF all
bands.
- “P.AMP2” activates 16 dB high-gain preamp
for 21 MHz band and above.
✔
What is the preamp?
The preamp amplifies received signals in the front end cir-
cuit to improve the S/N ratio and sensitivity. Select
“P.AMP1” or “P.AMP2” when receiving weak signals.
•Selects 6 dB, 12 dB or 18 dB attenuator,
or bypasses them.
✔
What is the attenuator?
The attenuator prevents a desired signal from distorting
when very strong signals are near the desired frequency
or when very strong electric fields, such as from a broad-
casting station, are near your location.
•Activates or selects fast, middle or slow
AGC time constant when pushed.
- The setting becomes “fast” in FM mode re-
gardless of this setting.
•Deactivates the AGC circuit when pushed
for 2 sec.
NOTE: While “AGC OFF” is selected, the
S-meter does not function.
✔
What is the AGC?
The AGC controls receiver gain to produce a constant
audio output level even when the received signal strength
is varied by fading, etc. Select “FAST” for tuning and se-
lect “MID” or “SLOW” depending on the receiving condi-
tion.
•Turns the VOX function ON and OFF when
pushed in non-CW modes. (p. 33)
•Enters the VOX set mode when pushed for
2 sec. in non-CW modes. (p. 33)
•Selects semi break-in, full break-in opera-
tion, or turns the break-in operation OFF
when pushed in CW mode.
✔
What is the VOX function?
The VOX function (voice operated transmission) starts
transmission without pushing the transmit switch or PTT
switch when you speak into the microphone; then, auto-
matically returns to receive when you stop speaking.
✔
What is the break-in function?
The break-in function toggles transmit and receive with
CW keying. Full break-in (QSK) can monitor the receive
signal during keying.
VOXVOX
OFFOFF
BK-INBK-IN
OFFOFF
AGCAGC
MIDMID
ATTATT
OFFOFF
P.AMPP.AMP
OFFOFF
METERMETER
PoPo
ANTANT
1
3
1
PANEL DESCRIPTION