Filter
Top Products
PAGE 10 — MT-62HS — PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
MT-62HS — OPERATION AND SAFETY DECALS
* Read operator’s manual carefully before use.
* Libre le manual attentivement avant utillsation.
* Bitte lesen Sie vor inbetriebnahme der Maschine de
Bedienungsanleitung sogfältig durch.
* Prima dell’ uso leggere attentamente il manuale.
* Lee com atenÇão o manual de instruÇões antes de
usar.
* Leer detenidamente el mamual de instrucciones
antes de usar la maquina.
CAUTION
ATTENZIONE
ATENÇAÕ
PRECAUCION
NPA-910 J
Oil
öl
I’ huile
SAE30
7~9 cc
NPA-961 E
NPA-769 J
READ OWNER’S SERVICE MANUALBEFORE OPERATING OR
SERVICING THISMACHINE.
ALWAYS KEEPUNAUTHORIZED, INEXPERIENCED,
UNTRAINED PEOPLEAWAYFROM THIS MACHINE.
MAKE SUREALL SAFETYDEVICES ARE OPERATIONAL
BEFORE THIS MACHINE IS STARTED. MAKE SURE ENGINE
IS TURNED OFFAND SPARK PLUG WIRE DISCONNECTED
BEFORE SERVICING THEMACHINE OR COMING IN
CONTACTWITH ANYMOVING PART. IF EQUIPMENT IS
POWERED BYAN ELECTRIC MOTOR DISCONNECT
ELECTRICAL PLUG.
NEVER LEAVE MACHINE UNATTENDED WHEN OPERATING.
ALWAYS STOP ENGINEANDALLOW ENGINE TO COOL
BEFOREADDING FUEL OR OIL.
NPA-329 J
To start, switch must be
in the “ ” positionON
NPA 293
3800 ~ 4000 RPM
P/N 920202930
NPA-984 J
CLEANING ELEMENT:
Remove the element from the pre-cleaner
Clean the element with solvent
Apply SAE30 motor oil with 7~9 cc, and
squeeze out excess oil before re-installing.
NPA-963 J
CAUTION
NPA-581 J
P/N 920100240
P/N NPA-769
P/N 920209610
P/N 920203290
P/N 920205810
P/N 920209100
P/N 920108310
P/N 920209840
When you stop
the engine, be
sure to close
the fuel cock
NPA-399 J
P/N 920203990
P/N NPA-963
NAMEPLATE
CONTACT MULTIQUIP
SERVICE DEPT.
NP-831 J
CLEAN THE ELEMENT WITH KEROSENE WHEN DIRTY. AFTERTHE
CLEANING, LUBRICATE IT MIXED OIL(KEROSENE 2~4: ENGINE OIL
1), SQUEEZE OUT THE OIL,AND REPLACE IT.AND CLEAN IT MORE
OFTEN WHEN OPERATING IN DUSTY CONDITIONS.
NOTICE
1. Check that all bolts are tight.
2. Before operation, check oil level at the sight gauge located
on the operator’s side of the oil tank. Fill the oil tank to the
“H” level using only outboard (2-stroke) oil.
3. Fill the fuel tank. Use only regular unleaded gasoline.
4. To start the engine: Turn the ignition switch to the “on”
position. Open the fuel-cock located under the fuel tank.
Close the choke lever located on the carburetor and pull
starter rope. When engine starts, open choke fully.
5. Should the engine become difficult to start, open the drain
cock located on the lower side of the crankcase and discharge
any excess fuel by cranking the engine 2 or 3 times.
6. Allowthe engine to warm up for 4 to 5 minutes before operation.
7. To begin operation, move the throttle lever quickly from the
“start” to the “run” or “on” position.
8. Remember to close the engine drain-cock after starting to
ensure proper operation.
9. When operation is complete, stop the engine by turning the
ignition switch to the “off” position.
10. Note: Transport the machine with the fuel-cock in the “off”
position only.
5 MM (3/16”)
PROPER SPONGE
INSTALLATION
NPA 398
J
P/N 920203980
DO NOT ALLOW WATER
TO ENTER FUELAND OIL TANKS
NP-599 J
P/N 920205990
SAE 10W-30
Motor Oil
NPA-195 J
P/N 920201950