Filter
Top Products
■ Front panel
(continued)
#0
LOCK/SPEECH SWITCH [LOCK/SPEECH]
➥Push momentarily to toggle the dial lock function
ON and OFF. (p. 46)
➥Pushing for 1 sec. announces the S-meter indi-
cation and the selected readout frequency when
an optional UT-102 is installed. (p. 74)
#1 RIT/
∂∂
TX CONTROL [RIT/
∂∂
TX] (p. 34)
Shifts the receive and/or transmit frequency without
changing the transmit and/or receive frequency
while the RIT and/or ∂TX functions are ON.
•Rotate the control clockwise to increase the frequency,
or rotate the control counterclockwise to decrease the
frequency.
•The shift frequency range is ±9.999 kHz in 1 Hz steps
(or ±9.99 kHz in 10 Hz steps).
#2 RIT SWITCH [RIT] (p. 34)
➥
Turns the RIT function ON and OFF when pushed.
•Use the [RIT/∂TX] control to vary the RIT frequency.
➥Adds the RIT shift frequency to the operating fre-
quency when pushed for 1 sec.
✔
What is the RIT function?
The RIT (Receiver Incremental Tuning) shifts the receive fre-
quency without shifting the transmit frequency.
This is useful for fine tuning stations calling you on an off-fre-
quency or when you prefer to listen to slightly different-
sounding voice characteristics, etc.
#3
∂∂
TX SWITCH [
∂∂
TX] (p. 34)
➥Turns the ∂TX function ON and OFF when
pushed.
•Use the [RIT/∂TX] control to vary the ∂TX frequency.
➥Adds the ∂TX shift frequency to the operating
frequency when pushed for 1 sec.
✔
What is the
∂∂
TX function?
The ∂TX shifts the transmit frequency without shifting the re-
ceive frequency. This is useful for simple split frequency op-
eration in CW, etc.
#4 CLEAR SWITCH [CLEAR] (p. 34)
Clears the RIT/∂TX shift frequency when pushed
for 1 sec. or when pushed momentarily, depending
on the quick RIT/∂TX clear function setting
(p. 72).
#5 CW PITCH CONTROL [CW PITCH]
(outer control; p. 29)
Shifts the received CW audio pitch and monitored
CW audio pitch without changing the operating fre-
quency.
#6 MANUAL NOTCH FILTER CONTROL [NOTCH]
(inner control; p. 26)
Varies the peak frequency of the manual notch fil-
ter to pick out a receive signal from interference
while the manual notch function is ON.
•Notch filter center frequency:
SSB : 0 Hz to 5100 Hz
CW : –900 Hz + CW pitch freq. to 4200 Hz + CW
pitch freq.
AM : –5100 Hz to 5100 Hz
NOTCH
CW PITCH
Lower frequency Higher frequency
Approx. 300 Hz
Approx. 900 Hz
Lower frequency Higher frequency
NOTCH
CW PITCH
RIT/∂TX
Low shift High shift
6
2
PANEL DESCRIPTION
NB NR
BAL NR
COMP BK-IN DELAYKEY SPEED
LOCKTX
RX
TWIN PBT
CW PITCH
F-1 F-2 F-3 F-4 F-5
REC/PLAY
LOCK/SPEECH
RIT/ TX
TXRIT CLEAR
SPLIT
MP-W MP-R
DUAL
WATCH
VFO/
MEMO
MAIN/
SUB
CHANGE
1.8
1
3.5
2
7
3
10
4
14
5
18
6
21
7
24
8
28
9
GENE
50
0
F-INP
ENT
Y
Z
MW
M-CL
TS
XFC
CEIVER
756PRO™
PBT CLR NOTCH
NOTCH
SSB
CW/RTTY
AM/FM FILTER EXIT/SET
$7 $6 $5
$1
$0
#9
#4
#6
#5
#3
#8
#7
#2
#1
#0
$2$3$4