Kenwood TS-480HX Marine Radio User Manual


 
53
11 MEMORY FEATURES
98~00lennahC a 99~09lennahC
ycneuqerfXR
a
ycneuqerfXR/XT
)xelpmis(
ycneuqerfXT
a
XRrofedoM
a
XR/XTrofedoM
)xelpmis(
XTrofedoM
a
petsycneuqerfXR
a
ycneuqerfXR/XT
)xelpmis(pets
petsycneuqerfXT
a
ycneuqerfenoT
a
ycneuqerfenoT
ycneuqerfSSCTC
a
ycneuqerfSSCTC
SSCTC/enoT
sutatsFFO/NO
a
SSCTC/enoT
sutatsFFO/NO
emaNyromeM
a
emaNyromeM
lennahCyromeM
FFO/NOtuokcoL
a
lennahCyromeM
FFOtuokcoL
99~09lennahC a 98~00lennahC
ycneuqerfXR/XT
a
ycneuqerfXR
a
ycneuqerfXT
XR/XTrofedoM
a
XRrofedoM
a
XTrofedoM
ycneuqerfXR/XT
)xelpmis(pets
a
petsycneuqerfXR
a
petsycneuqerfXT
ycneuqerfenoT
a
ycneuqerfenoT
ycneuqerfSSCTC
a
ycneuqerfSSCTC
SSCTC/enoT
sutatsFFO/NO
a
SSCTC/enoT
sutatsFFO/NO
emaNyromeM
a
emaNyromeM
lennahCyromeM
FFO/NOtuokcoL
a
lennahCyromeM
FFOtuokcoL
When copying a memory channel 90 ~ 99 a
channel 90 ~ 99, Memory Channel Lockout status
changes to OFF, regardless of the original channel
settings.
The tables above illustrate how data is transferred
between memory channels.
STORING FREQUENCY RANGES
Memory channels 90 to 99 allow you to store
frequency ranges for VFO tuning and Program Scan.
Program Scan is described in the next chapter. To
tune or scan frequencies within a specified range,
store the start and end frequencies for that range in
advance.
1 Press [A/B / M/V] to select VFO A or VFO B.
2 Select the desired start frequency.
3 Press [QMI/ M.IN] (1 s) to enter Memory Scroll
mode.
•To exit Memory Scroll mode and abort the
storage process, press [MTR/ CLR].
4 Turn the MULTI control, or press Mic [UP]/ [DWN]
to select a memory channel in the range of 90 to
99.
•You can also select a channel by entering a
2-digit number. Press [9], [0] for example.
5 Press [QMI/ M.IN] to store the start frequency in
the memory channel.
“ENDINPUT” appears on the sub-display.
6 Turn the Tuning control or MULTI control to select
the end frequency.
7 Press [QMI/ M.IN] to store the end frequency in
the memory channel.
The previous data stored in the channel is
overwritten.
Confirming Start/ End Frequencies
Use this procedure to check the start and end
frequencies that you stored in channels 90 to 99.
1 Press [A/B / M/V] (1 s) to enter Memory Recall
mode.
2 Turn the MULTI control, or press Mic [UP]/
[DWN] to select a memory channel from 90 to
99.
3 Press [ ] to check the start frequency and [ ]
to check the end frequency.