Filter
Top Products
63
13 OPERATOR CONVENIENCES
DISPLAY
BRIGHTNESS
The brightness of the LCD display can be selected
from OFF, and 1 to 4 by accessing Menu No. 00.
1 Press [MENU/ F.LOCK], then turn the MULTI
control to access Menu No. 00.
2 Press [ ]/ [ ] to select “oFF”, “1”, “2”, “3”, or “4”.
3 Press [MENU/ F.LOCK] to store the setting and
exit Menu mode.
KEY ILLUMINATION
The Remote Control panel key illumination can be
switched ON or OFF.
1 Press [MENU/ F.LOCK], then turn the MULTI
control to access Menu No. 01.
2 Press [ ]/ [ ] to select “oFF” or “on”.
3 Press [MENU/ F.LOCK] to store the setting and
exit Menu mode.
LINEAR AMPLIFIER CONTROL
When you connect an external HF or 50 MHz linear
amplifier to the transceiver using the REMOTE
connector, select “1”, “2”, or “3” to activate the
internal relay and/ or DC output (12 V) so you can
interface with the HF/ 50 MHz linear amplifier {page
80}. The DC output (12 V) works without any
annoying chattering sounds (“1”) but the output
current is limited to 10 mA. If your linear amplifier
control circuit draws more than DC 12 V/ 10 mA, use
the relay switching (“2” or “3”) instead.
Also, some linear amplifiers require a long
transmission delay time because of the slow antenna
relay switching time. In this case, select “3” for the
slow switching (25 ms delay).
1 Press [MENU/ F.LOCK], then turn the MULTI
control to select Menu No. 28 (HF) or
29 (50 MHz).
2 Press [ ]/ [ ] to select “oFF”, “1”, “2”, or “3”.
retemaraP lortnoc.pmAraeniL
)tluafed(FFoslortnocllAdelbasiD
1
)V21(tuptuoCD
yaleR
yaledXT
delbanE
delbasiD
sm01
2
)V21(tuptuoCD
yaleR
yaledXT
delbanE
delbanE
sm01
3
)V21(tuptuoCD
yaleR
yaledXT
delbanE
delbanE
sm52
Note:
If CW Full Break-in is enabled, 10 ms transmission delay is
applied regardless of the settings in Menu Nos. 28 and 29.
LOCK FUNCTIONS
FREQUENCY LOCK FUNCTION
Frequency Lock disables some keys and controls to
prevent you from accidentally activating a function or
changing the current settings.
Press [MENU/ F.LOCK] (1 s) to turn the Frequency
Lock function ON or OFF.
•“” appears while this function is ON.
The following keys and controls are disabled by
Frequency Lock:
gninuT lortnoc ITLUM lortnocTNE
NI.M/IMQLES.GS/NACSEDOM
T.WCM/RMQ s OFVV/M/B/A
TILPS/B=AzHM]PU[ciM
]NWD[ciM
Note:
◆
After activating Frequency Lock, the
MULTI
control and
[ ]
/
[ ]
are still available in Menu mode.
◆
After activating Frequency Lock, you can still change the
transmission frequency with the
Tuning
control while in TF-SET
mode.
◆
After activating Frequency Lock, the
MULTI
control is still
available for selections other than frequency and memory
channel changes.
◆
After activating Frequency Lock,
[MTR/ CLR]
may be available in
some situations.
TUNING CONTROL LOCK FUNCTION
The Tuning control lock function disables the Tuning
control. The function can be used in the following
situations:
•You do not want to change the operating
frequency while you are driving the car.
To use the Tuning control lock function, first assign
the function to the PF key on the Remote Control
panel (or Mic PF keys).
1 Press [MENU/ F.LOCK] and turn the MULTI
control to select Menu No. 48.
2 Press [ ]/ [ ] to select “65”.
3 Press [MENU/ F.LOCK] to store the setting and
exit the Menu mode.
4 Press [PF].
•“” appears and the Tuning control is now locked.
To return to normal operation, press [PF] again.