Filter
Top Products
41
0(025<)($785(6
0(025<&+$11(/6
This transceiver provides you with 110 memory
channels, numbered 00 to 99 and P0 to P9, for
storing operating frequency data, modes, and other
information. Memory channels 00 to 99 are called
Conventional Memory Channels. Memory channels
P0 to P9 are designed for programming VFO tuning
ranges and scan ranges. The data you can store is
listed below.
Conventional memory channels are used for storing
data you will often recall. For example, you may store
the frequency where you regularly meet your club
members.
Parameter
Channel
00 ~ 99
Channel
P0 ~ P9
RX Frequency Yes
Yes
1
(simplex)
TX Frequency Yes
Mode for RX Yes
Yes
1
(simplex)
Mode for TX Yes
Programmable VFO
Start/ End Frequencies
No Yes
Tone Frequency Yes Yes
CTCSS Frequency Yes Yes
Tone/ CTCSS ON/ OFF
Status
Yes Yes
Memory Name Yes Yes
Memory Channel Lockout
ON/ OFF
Yes
1
Yes
1
1
Changing the data after recalling a memory channel overwrites
the contents of the channel.
6725,1*'$7$,10(025<
There are 2 methods used for storing transmission/
reception frequencies and associated data in memory
channels 00 to 99. Use either method, depending
on the relationship of the reception and transmission
frequencies you store:
• Simplex channels:
RX frequency = TX frequency
• Split-frequency channels:
5;IUHTXHQF\7;IUHTXHQF\
Memory channels P0 to P9 can also be used as
simplex channels.
Note: When RIT or XIT is ON, the frequency that includes the
RIT or XIT offset will be stored.
Q 6LPSOH[&KDQQHOV
1 Press [A/B (A=B)] to select VFO A or VFO B.
•“
” or “ ” appears to show which VFO
is selected.
2 Select the frequency, mode, etc., to be stored.
3 Press [M.IN] to enter Memory Scroll mode.
•“
” appears.
• To exit Memory Scroll mode and abort the
storage process, press [CLR].
4 Turn the MULTI/CH control, or press Mic [UP]/
[DWN] to select a memory channel.
• You can also select a channel by entering
a 2-digit number, such as 12, using the
numeric keys. Press [ENT], [1.8 (1)], [3.5
(2)] for example.
5 Press [M.IN] again to store the data.
• The previous data stored in the channel is
overwritten.
Q
6SOLW)UHTXHQF\&KDQQHOV
1 Press [A/B (A=B)] to select VFO A or VFO B.
•“
” or “ ” appears to show which VFO
is selected.
2 Select the frequency, mode, etc., to be stored.
• This frequency and mode will be used for
transmitting.
3 Press [A/B (A=B)] to select the other VFO.
4 Select the reception frequency and mode.
5 Press [SPLIT].
•“
” appears.
6 Press [M.IN] to enter Memory Scroll mode.
• To exit Memory Scroll mode and abort the
storage process, press [CLR].
7 Turn the MULTI/CH control, or press Mic [UP]/
[DWN] to select a memory channel.
• You can also select a channel by entering
a 2-digit number, such as 12, using the
numeric keys. Press [ENT], [1.8 (1)], [3.5
(2)] for example.
8 Press [M.IN] to store the data.
• The previous data stored in the channel is
overwritten.
Note: When subtone frequencies differ between TX and RX
while performing memory-VFO split operation, the subtone
frequency for TX will be stored in the memory channel.