Filter
Top Products
64
23(5$725&219(1,(1&(6
6.<&200$1',,
Sky Command II allows you to remotely control the
TS-590S transceiver from a separate location.
If you have more than 2 TH-D7A/ TH-D72A/E/
TM-D710A/ TM-V71A + RC-D710/ TM-D700A
transceivers (K type), you can perform Sky Command
II operation to remotely control the HF/ 50 MHz band
of your TS-590S transceiver.
You will use one transceiver (TH-D7A, TH-D72A/E,
TM-D710A, TM-V71A + RC-D710, or TM-D700A) as a
remote control unit, called a “Commander”. The other
VHF/ UHF transceiver (TH-D7A, TH-D72A/E,
TM-D710A, TM-V71A + RC-D710, or TM-D700A) with
the TS-590S transceiver is called the “Transporter”.
This TH-D7A, TH-D72A/E, TM-D710A, TM-V71A +
RC-D710, or TM-D700A transceier will function as
an interface between the Commander (a remote
control unit) and the HF/ 50 MHz band of the TS-590S
transceiver.
This system allows you, for example, to watch for and
hunt DX while washing your car, or to operate the HF
transceiver while relaxing in your car, living room, or
patio, instead of actually operating inside your shack.
Note: Operation of Sky Command II may not been permitted in
certain countries. Check your local laws before operating.
6.<&200$1',,',$*5$0
VHF freq.
Commander Transporter
Audio
Audio
UHF freq.
Audios
Control commands
tResponse
Control commands
tResponse
35(3$5$7,21
Although you can use a TH-D7A, TH-D72A/E,
TM-D710A, TM-V71A + RC-D710, or TM-D700A
transceiver as a “Commander” (an external remote
control unit), the following procedure shows how
to set up your TS-590S and TH-D7A, TH-D72A/E,
TM-D710A, TM-V71A + RC-D710, or TM-D700A
transceivers as a “Transporter” at a base station and
the TM-D710A, TM-V71A + RC-D710, or TM-D700A
transceiver as a “Commander”.
6WDUWLQJ6N\&RPPDQG,,RSHUDWLRQ
After you have completed setting up the following,
you can start Sky Command II operation. Without
programming these parameters, you cannot use Sky
Command II.
TS-590S + TH-D7A/ TH-D72A/E/ TM-D700A/
TM-D710A/ TM-V71A + RC-D710 (Transporter)
Setup:
1 Configure the TH-D7A, TH-D72A/E, TM-D710A,
TM-V71A + RC-D710, or TM-D700A as a
“Transporter” and connect all the necessary cables
to the TS-590S transceiver.
2 Select a frequency (HF/ 50 MHz band) on the
TS-590S transceiver.
3 On the TS-590S, press [MENU], then turn MULTI/
CH control to select Menu No. 61.
4 Press [M.IN]/ [SCAN (SG.SEL] to select the the
desired communication speed.
5 Select the same communication parameters to
match the TH-D7A, TH-D72A/E, TM-D710A,
TM-V71A + RC-D710, or TM-D700A transceiver
6 Press [MENU] to exit Menu mode.
7 Configure and start the Transporter mode on the
TH-D7A, TH-D72A/E, TM-D710A, TM-V71A +
RC-D710, or TM-D700A transceiver.
• Refer to the respective instruction manuals of
the TH-D7A, TH-D72A/E, TM-D710A, TM-V71A
+ RC-D710, or TM-D700A for information on
how to connect, configure, and operate the
transceivers for Sky Command II.