Filter
Top Products
1-19
PCS-1/1P
DHCP Mode
Host Name
IP Address
Network Mask
Gateway Address
DNS Address
Gatekeeper Mode
Gatekeeper
Address
User Alias
User Number
SNMP Mode
Trap Destination
Community
Description
Location
Contact
NAT Mode
NAT Address
Packet Resent
Request
Adaptive Rate
Control
LAN Mode
Port Number Used
TCP Port Number
UDP Port Number
TOS
IP Precedence
Low Delay
High Throughput
High Reliability
Minimum Cost
Diffserve
PPPoE
PPPoE User Name
PPPoE Password
Fixed IP for
PPPoE
Fixed IP Address
for PPPoE
PPPoE DNS
Primary DNS
Secondary DNS
Page
1/8
Page
2/8
Page
3/8
Page
4/8
Page
5/8
Page
6/8
Page
7/8
Page
8/8
Initial value
Off★
Blank★
Blank★
Blank★
Blank★
Blank
Off
Blank
Blank
Blank
Off
Blank
Public
Videoconference
Device
Blank
Blank
Off
Blank
On
On
Auto Negotiation
Default
2253
49152
OFF
0
Off
Off
Off
Off
0
Off
Blank
Blank
Off
Blank
Obtain
automatically
Contents of setting
Set whether to use DHCP (Dynamic Host Configuration Protocol). Set to
“Auto” when automatically acquiring an IP address, net mask, gateway address,
and DNS address. Set to “Off” when not automatically acquiring them.
Set the host name of this unit.
Set the IP address of this unit.
Set the network mask of this unit.
Set a default gateway address.
Set a DNS (Domain Name System) server address.
Set to “On” when using a gatekeeper and set to “Off” when not using it. Set to
“Auto” when automatically searching a gatekeeper.
Set the IP address of a gatekeeper.
Set the user name (H.323 alias) registered in a gatekeeper.
Set the user number (E.164 number) registered in a gatekeeper.
Set to “On” when enabling the service of an SNMP (Simple Network
Management Protocol) agent. Set to “Off” when disabling it.
Set the IP address of an SNMP manager that transmits a trap.
Set the community name that an SNMP manager manages. Usually, set to
“Public”.
This is the description of this device. It has been entered as “Videoconference
Device”. Cannot be changed.
Set the place in which this unit is installed.
Set the information on the administrator of this unit.
Set to “On” when connecting this unit to the local network in which NAT
(Network Address Translation) is used. Set to “Off” when not connecting it.
Set the IP address on the global side that NAT uses.
Set to “On” when requesting retransmission with the packets lost during
communication. Set to “Off” when not requesting it.
Set to “On” when optimizing the LAN bandwidth. Set to “Off” when not
optimizing it.
* This item is fixed to “On” when “Packet Retransmission Request” is “On”.
Select the interface type and communication mode during LAN connection.
Select whether to fix the TCP port number and UDP port number.
User setting: The port number that the user sets is used.
Default value: The default port number is used.
TCP port number 2253 and UDP port number 49152 are set.
Set the TCP port number when “Port Number Used” is “Custom”.
Set the UDP port number when “Port Number Used” is “Custom”.
Select the definition of a TOS (Type of Service) field. Set to “Off” when not
defining the TOS field. Select “IP Precedence” when defining in IP Precedence
and select “Diffserve” when defining in Diffserve.
* For the items below, the display dynamically varies depending on the
selection.
Enter IP Precedence values (0 to 7).
Select low delay bit On/Off of TOS field.
Select high throughput bit On/Off of TOS field.
Select high reliability bit On/Off of TOS field.
Select minimum cost bit On/Off of TOS field.
Enter Diffserve value (0 to 64).
Select PPPoE termination On/Off using this unit.
Enter the PPPoE connection user name (account) acquired from a provider.
Enter the PPPoE connection password acquired from a provider.
Set to “On” when acquiring the PPPoE connection-fixed IP address. Set to
“Off” when automatically acquiring for each session.
Enter the fixed IP address acquired from a provider when “Fixed IP for PPPoE”
is “On”.
Select “Obtain automatically” when acquiring the IP address of the DNS server
from the server during PPPoE connection. Select “Set” when the fixed IP
address exists.
Enter the IP address of the primary DNS server when “PPPoE DNS” is “Set”.
Enter the IP address of the secondary DNS server when “PPPoE DNS” is “Set”.
Item
LAN Setup
During IP Precedence selection
During Diffserve selection