Filter
Top Products
2-17
PCS-1/1P
For loading of application
1. Display a service menu.
2. Insert the Memory Stick, in which the application
software of the version to be loaded is recorded, into a
Memory Stick slot.
3. Select “Load application” using ↑, ↓, ←, and →
buttons of a remote controller and press the ENTER
button.
4. A confirmation message on whether to execute is
displayed.
5. To execute, select “OK” and press the ENTER button.
The screen display during loader execution then
appears. After completion, a launcher menu is
displayed. To cancel execution, select “Cancel” and
press the ENTER button. The current display returns
to a service menu.
6. Push in the Memory Stick once and take out it.
n
Do not turn off the power or take out a Memory Stick until
the launcher menu is displayed.
For command input
1. Display a service menu.
2. Select “Command” using ↑, ↓, ←, and → buttons of a
remote controller and press the ENTER button.
A key guidance is then displayed.
3. Enter the commands in a command list from a remote
controller.
m
. To set two or more commands, put a one-character
blank between the commands and then enter them.
. Set only one type of LAN interface. If not, the LAN
interface does not operate normally.
4. Select “Save” using ↑, ↓, ←, and → buttons of a
remote controller and press the ENTER button.
A set menu is then displayed.
5. When a LAN interface is set (including the case where
the setting is returned to the initial value), restart the
main unit using the power switch of a communication
terminal.
To stop setting
Select “Cancel” using ↑, ↓, ←, and → buttons of a remote
controller and press the ENTER button, or press the return
button of a remote controller.
n
Do not enter commands other than shown in a command
list. The internal operation mode may be changed in this
case.
Contents of functions
1) Command
The internal operation mode of the main unit is
changed for a test and service.
Command list
m
. To set two or more types of commands, put a one-
character blank between commands.
. The validated command can be confirmed in a command
column at all times.
. Do not enter commands other than described in the table.
This may change the internal operation mode.
Command
SMS
KV66
WBxxxXyyy
YCLP**
YLVL**
D2B
PWD1
SMFF
BMR0
SMSTEST
PROJ
POFF
Description
Validates an SMS function.
Sets a KV-29FX66E monitor when it is used.
Using an IR repeater, this command sets the
input selection of a KV-29FX66E monitor to 3
after the power is turned on.
An IR output is changed so that the
command during power-off sequence is sent
properly. The setting of the IR repeater
mode is invalided when this command is
specified.
Sets the size (height x width) of the
whiteboard used.
Clips the luminance value in a menu to the
specified value.
The section having the luminance of more
than the specified value is clipped to the
specified value. (** is one of 80, 90, A0, B0,
C0, D0, and E0 values.)
Shifts the luminance value in a menu
downward proportionally to the specified
value.
As a value increase, the whole screen
becomes darker.
Since all values are shifted, the black side
seems crushed.
(** is a value of 0 < ** < 80 in decimal.)
Sets ISDN (2B) to the default value using a
dial menu. Usually, set to LAN.
The password for an administrator invalidates
the password lock of a phone book when a
setting super-user password is blank in a
column.
Fixes a sub-monitor to the remote video.
Sets the bonding mode to Revision 0 (in
which up to the conventional seven-digit
address number can be used).
Displays SAB without connecting with the
SMS server.
Sends the remote control code for the projector.
Makes the packet loss indicator non-display.