Filter
Top Products
12
AMPHOS DC MANUAL
© 2002 Design, 2012 Doc. No. 12-5301-r01 (12/17/12)
Fig. 17 - SET WATCH CDT
Fig. 20 - LAP RECALL
Fig. 18 - CHRONO STATUS
(not running)
Fig. 21 - DAILY ALARM
Fig. 22 - SET DAILY ALARM
Fig. 19 - CHRONO STATUS
(Lap in progress)
sec_.01 sec
hr:min
Set CDT, information includes (Fig. 17):
> Graphic SEt with last Time (hr:min) set, Hour digits flashing.
> Graphic CDT.
• S (press/hold) will scroll upward through the Hour Set Points in 1 hour increments at a rate of 8 per second.
• S (< 2 sec) will step upward through the Set Points one at a time.
• A (< 2 sec) will save the Hour setting and flash the Minute digits.
• S (press/hold) will scroll upward through the Minute Set Points in 1 minute increments at a rate of 8 per second.
• S (< 2 sec) will step upward through the Set Points one at a time.
• A (< 2 sec) will save the Minutes setting and revert to the CDT Status screen with the graphic OFF flashing in place of SEt.
• S (< 2 sec) will toggle from OFF to ON, starting countdown.
• M (2 sec), or no button press for 2 min, will revert to Watch Default Time.
CHRONOGRAPH STATUS (Stop Watch, Lap Timer), information includes (Fig. 18, 19):
> 0:00:00.00, or total elapsed run time (hr:min & sec. 1/100th sec) if previously started and running.
> Graphic CHRO if not running, or LAP1 (2 to 9, the one in progress) if running.
• S (< 2 sec) will Start the Timer which will begin counting up from 0:00:00.00 to 9:59:59.99 (hr:min_ _sec.1/100th sec) in
increments of .01 (1/100th sec).
During the first 4 seconds the 1/100th second values will be displayed after which 2 dashes ( . - - ) will be displayed.
The 1/100th values will be recorded and displayed when Laps are frozen and when later recalled.
• Subsequent presses of S (< 2 sec) will freeze Lap Times (LAP 1 through LAP 9). After 9 Laps are recorded, additional Laps
will replace LAP 9, shift the others to lower LAP numbers, while discarding LAP 1.
If the Timer reaches 9:59:59.99, it will stop and save that as a LAP. Subsequent presses of S will then have no effect.
• A (< 2 sec) will Stop the Timer and Recall LAP 1, displaying the graphic LAP1 and Lap Time. Repeat presses will display
other Laps (2 to 9).
• A (2 sec) will Stop the Timer and Reset the Time to 0:00:00.00.
• M (< 2 sec) will access Daily Alarm Status.
• M (2 sec), or no button press for 2 min, will revert to Watch Default Time.
While the Chrono is running, it will remain on the screen until a button operation is performed. If another screen is accessed, it
will then continue to run in the background.
Upon descending on a dive, Chrono operation will be terminated and reset to 0:00:00.00.
DAILY ALARM STATUS, information includes (Fig. 21):
> Graphic ON (or OFF), flashing.
> Alarm Time last set (hr:min) with A (or P) icon.
> Graphic ALRM and alarm icon.
• S (< 2 sec) will toggle between ON and OFF.
>> If OFF is selected, alarm activation is disabled. Access to Set will be allowed.
>> If ON is selected, the alarm time set is enabled. Access to Set will be blocked.
• A + S (2 sec) will display the graphic SEt in place of OFF, allowing the Time to be set.
• M (< 2 sec) will revert to Watch Default Time.
• M (2 sec), or no button press for 2 min, will revert to Watch Default Time.
• L (press) will activate the Backlight.
Set Daily Alarm, information provided includes (Fig. 22):
> Graphic SEt.
> Alarm Time previously set (hr:min), Hour digits flashing.
> Graphic ALRM and alarm icon.
• S (press/hold) will scroll upward through the Hour Set Points in 1 hour increments at a rate of 8 per second.
• S (< 2 sec) will step upward through the Set Points one at a time.
• A (< 2 sec) will save the Hour setting and flash the Minute digits.
• S (press/hold) will scroll upward through the Minute Set Points in 1 minute increments at a rate of 8 per second.
• S (< 2 sec) will step upward through the Set Points one at a time.
• A (< 2 sec) will save the Minutes setting and revert to the Daily Alarm Status, the graphic OFF flashing in place of SEt.
• S (< 2 sec) will toggle from OFF to ON, starting countdown.
Once the Daily Alarm has been set and turned ON, it will run in the background while on the surface until turned OFF.
Alarm time is synchronized with the local Default Time selected for the current location. It will also run in the background
while in Dive Computer modes but will not sound the audible or flash the icon when the alarm time is reached during dives.