Mitsubishi Electronics FR-F740P Marine Battery User Manual


 
381
Initiating a fault (Pr.997).......................................................... 289
Input compensation of multi-speed and remote setting (Pr.
28) .............................................................................................. 106
Input terminal function selection (Pr. 178 to Pr. 189).........133
Input/output phase loss protection selection
(Pr. 251, Pr. 872) ................................................................. 175
Instantaneous power failure/undervoltage........................... 140
Insulation resistance test using megger............................... 344
Inverter installation environment ...............................................8
Inverter operation ready.......................................................... 140
Inverter outline dimension drawings ..................................... 350
Inverter output shutoff signal (MRS signal, Pr. 17)............. 136
Inverter placement..................................................................... 10
Inverter replacement ............................................................... 339
Inverter reset............................................................................. 133
Inverter run enable signal (FR-HC, MT-HC, FR-CV
connection) ............................................................................... 133
Inverter running........................................................................ 140
Inverter running and start command is ON..........................140
IPM motor control..................................................................... 140
IPM motor test operation (Pr.800) (IPM)................................ 82
J
Jog operation (Pr. 15, Pr. 16)................................................. 104
Jog operation selection........................................................... 133
L
Leakage currents and countermeasures ............................... 44
Life alarm................................................................................... 140
Load pattern selection (Pr. 14) .............................................. 100
Low-speed operation command ............................................ 133
M
Maintenance timer alarm (Pr. 503, Pr. 504) ........................ 285
Maintenance timer signal........................................................ 140
Manual torque boost (Pr. 0, Pr. 46) (IPM).............................. 87
Maximum/minimum frequency (Pr. 1, Pr. 2, Pr. 18)............. 96
Measurement of converter output voltage (across terminals
P/+ and N/-) .............................................................................. 344
Measurement of currents........................................................ 343
Measurement of inverter input power factor........................ 343
Measurement of inverter output frequency.......................... 344
Measurement of powers ......................................................... 342
Measurement of voltages and use of PT ............................. 342
Middle-speed operation command........................................ 133
Minimum motor rotation frequency (Pr.13).......................... 114
Mitsubishi inverter protocol
(computer link communication).......................................... 234
Modbus-RTU communication specifications (Pr. 331, Pr. 332,
Pr. 334, Pr. 343, Pr. 539, Pr. 549)......................................... 247
Motor protection from overheat (Electronic thermal relay
function) (Pr. 9, Pr. 51)............................................................117
Motor specification...................................................................360
Mounting the operation panel (FR-DU07) on the enclosure
surface......................................................................................... 32
Multi-speed setting operation (Pr. 4 to Pr. 6, Pr. 24 to Pr. 27,
Pr. 232 to Pr. 239) ...................................................................102
O
Operation mode at power ON (Pr. 79, Pr. 340) .................. 218
Operation mode selection (Pr. 79) ........................................ 206
Operation panel lock ............................................................... 310
Operation selection at communication error
(Pr.502, Pr.779).................................................................... 231
Output current detection ......................................................... 140
Output current detection function (Y12 signal, Y13 signal, Pr.
150 to Pr. 153, Pr. 166, Pr. 167) ........................................... 146
Output frequency detection .................................................... 140
Output stop ...............................................................................133
Output stop function (Pr.522) .................................................131
Output terminal function selection (Pr. 190 to Pr. 196) ......140
Overload warning .....................................................................140
P
Parameter copy.........................................................................301
Parameter list..............................................................................64
Parameter verification..............................................................302
Parameter write selection (Pr. 77) .........................................200
Password function (Pr. 296, Pr. 297) ............................203, 203
Periodic inspection ...................................................................332
Peripheral devices........................................................................4
PID control (Pr. 127 to Pr. 134, Pr. 241, Pr. 553, Pr. 554, Pr.
575 to Pr. 577, C42 (Pr. 934) to C45 (Pr. 935)) ..................261
PID control valid terminal ........................................................133
PID deviation limit.....................................................................140
PID forward/reverse action switchover .................................133
PID forward/reverse rotation output ......................................140
PID integral value reset ...........................................................133
PID lower limit ...........................................................................140
PID output interruption.............................................................140
PID upper limit...........................................................................140
Power failure signal (Y67 signal) ...........................................168
Power failure-time deceleration-to-stop function (Pr. 261 to
Pr. 266 ) .....................................................................................169
Power supply harmonics ...........................................................48
Pressure test .............................................................................344
Protrusion of heatsink of the FR-F740P-185K or more......361
PTC thermistor input ................................................................133
PU contrast adjustment (Pr. 991)...........................................298
PU display language selection (Pr. 145) ..............................295
PU operation external interlock ..............................................133
PU operation mode ..................................................................140
PU/External operation switchover..........................................133
PU/NET operation switchover ................................................133
Pulse train output of output power.........................................140
Pulse train output of output power (Y79 signal, Pr. 799) ...149
R
Regeneration avoidance function
(Pr. 665, Pr. 882 to Pr. 886)................................................279
Regenerative brake pre-alarm................................................140
Remote output...........................................................................140
Remote output function (REM signal, Pr. 495 to Pr. 497)..148
Remote setting (acceleration).................................................133
Remote setting (deceleration) ................................................133
Remote setting (setting clear).................................................133
Remote setting function (Pr. 59) ............................................106
Replacement of parts...............................................................335
Replacement of the FR-A100 series....................................365
Replacement of the FR-F500 series .....................................364
Reset selection/disconnected PU detection/PU stop selection
(Pr. 75) .......................................................................................198
Response level of analog input and noise elimination
(Pr. 74) ...................................................................................192
Retry function (Pr. 65, Pr. 67 to Pr. 69) ................................172
Reverse rotation command.....................................................133
Reverse rotation prevention selection (Pr. 78) ....................201
RS-485 terminal block ...............................................................33
S
Second function selection .......................................................133
Second output frequency detection.......................................140
Selection of a regenerative brake and DC feeding (Pr. 30, Pr.
70)...............................................................................................125
Selection of automatic restart after instantaneous power
failure, flying start .....................................................................133
Setting multiple parameters as a batch (Pr.999).................290
Setting of the acceleration and deceleration time (Pr.7, Pr.8,