Filter
Top Products
70
Parameter list
Power failure stop
261
Power failure stop selection 0, 1, 2, 21, 22 1 0 169
262
Subtracted frequency at deceleration
start
0 to 20Hz 0.01Hz 3Hz 169
263
Subtraction starting frequency 0 to 400Hz, 9999 0.01Hz 60Hz 169
264
Power-failure deceleration time 1 0 to 3600/ 360s 0.1/0.01s 5s 169
265
Power-failure deceleration time 2
0 to 3600/ 360s,
9999
0.1/0.01s 9999 169
266
Power failure deceleration time
switchover frequency
0 to 400Hz 0.01Hz 60Hz 169
⎯
267
Terminal 4 input selection 0, 1, 2 1 0 185
⎯
268
Monitor decimal digits selection 0, 1, 9999 1 9999 152
⎯
269
Parameter for manufacturer setting.
Do not set.
Password
function
296
Password lock level
0 to 6, 99, 101 to 106,
199, 9999
1 9999 203
297
Password lock/unlock
(0 to 5), 1000 to 9998,
9999
1 9999 203
⎯
Rotation direction detection selection
at restarting
0, 1, 9999 1 9999 162
299
RS-485 communication
331
RS-485 communication station
number
0 to 31(0 to 247) 1 0 229
332
RS-485 communication speed
3, 6, 12, 24,
48, 96, 192, 384
196229
333
RS-485 communication stop bit
length
0, 1, 10, 11 1 1 229
334
RS-485 communication parity check
selection
0, 1, 2 1 2 229
335
RS-485 communication retry count 0 to 10, 9999 1 1 229
336
RS-485 communication check time
interval
0 to 999.8s, 9999 0.1s 0s 229
337
RS-485 communication waiting time
setting
0 to 150ms, 9999 1 9999 229
338
Communication operation command
source
0, 1 1 0 219
339
Communication speed command
source
0, 1, 2 1 0 219
340
Communication startup mode
selection
0, 1, 2, 10, 12 1 0 218
341
RS-485 communication CR/LF
selection
0, 1, 2 1 1 229
342
Communication EEPROM write
selection
0, 1 1 0 230
343
Communication error count ⎯ 10247
Remote
output
495
Remote output selection 0, 1, 10, 11 1 0 148
496
Remote output data 1 0 to 4095 1 0 148
497
Remote output data 2 0 to 4095 1 0 148
—
502
Stop mode selection at
communication error
0 to 3 1 0 231
Maintenance
503
Maintenance timer 0 (1 to 9998) 1 0 285
504
Maintenance timer alarm output set
time
0 to 9998, 9999 1 9999 285
⎯
505
Speed setting reference 1 to 120Hz 0.01Hz 60 150
⎯
522
Output stop frequency 0 to 400Hz, 9999 0.01Hz 9999 131
⎯
539
Modbus-RTU communication check
time interval
0 to 999.8s, 9999 0.1s 9999 247
Function Parameters
Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting