Filter
Top Products
17
F.10 v.3 OPERATING MANUAL
© 2002 Design, 2014 Doc. No. 12-5380-r01 (7/15/14)
• A (hold) - to scroll upward through Minute Set Points (8/sec) from 0: to 59: in increments of 1: (min).
• A (< 2 sec) - to step upward through Minute Set Points.
• M (< 2 sec) - to step back through Set Points.
• S (< 2 sec) - to save the Minute setting and flash the Seconds digits.
• A (hold) - to scroll upward through Seconds Set Points (8/sec) from :00 to :59 in increments of :01 (sec).
• A (< 2 sec) - to step upward through Seconds Set Points.
• M (< 2 sec) - to step back through Set Points one at a time.
• S (< 2 sec) - to save the CDT setting and revert to the CDT Status screen with SEt flashing, allowing ON or OFF to be selected
as previously described.
• S (2 sec) - to revert to CDT Setup, if no setting change.
• M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.
• L (< 2 sec) - to toggle the Backlight On/Off.
Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
------------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------------
SURFACE SET MODES
To access: SURF MAIN >> ALT 1 >> ALT 2 >> CDT >> SET A >> SET U.
• A (< 2 sec) to access and step through the sequence.
> Set Points can also be changed using the ACI PC Interface program.
> Settings remain at the values set until changed.
SET ALARMS
Sequence: Lead-in >> AUD >> SRT >> EDT >> RDI >> DD1 to DD3.
• A (< 2 sec), while viewing CDT Lead-in, to access Set Alarms Lead-in.
The Set Audible feature provides complete OFF control of the Audible and its associated LED warning light. When set OFF, no
beeps will be emitted and the light will not flash when an alarm condition occurs, which some divers prefer during select activities.
Icons and messages will still flash and the Backlight will still come On.
The SRT (Surface Recovery Time) Alarm provides an alert when a set 'recovery time' has elapsed after surfacing from a dive.
The EDT (repeating Elapsed Dive Time) Alarm repeats each time the Time Interval set is reached during operation in Dive Mode.
The RDI (Repeating Depth Interval) Alarm repeats each time the Depth Interval set is reached, except when the DD alarms strike. If a
series of descents, ascents, descents is made, the alarm will activate during each of the Descents.
The DD1 to DD3 (Descending Depth) Alarms are set and operate in sequence while descending.
At any time while entering settings -
• M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.
• L (< 2 sec) - to toggle the Backlight On/Off.
Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
Set Alarms Lead-in, information includes (Fig. 27):
> Graphics GoTo and SEt A.
• S (< 2 sec) - to access Set Audible.
• A (< 2 sec) - to step forward to Set Utilities Lead-in.
• M (< 2 sec) - to step back to CDT Lead-in.
Set Audible Alarm, information includes (Fig. 28):
> Graphic AUD.
> Graphic OFF (or ON), flashing upon access.
• A or M (< 2 sec) - to toggle between OFF and ON.
• S (2 sec) - to step back to Set Alarms Lead-in.
• S (< 2 sec) - to save the setting and access Set SRT Alarm.
Fig. 27 - SET ALARMS
LEAD-IN
Fig. 28 - SET AUDIBLE
ALARM