Filter
Top Products
9
F.10 v.3 OPERATING MANUAL
© 2002 Design, 2014 Doc. No. 12-5380-r01 (7/15/14)
WATCH DEFAULT TIME
Default Time is the time that is displayed on the Watch until changed. It is also the time viewed during operation in DC (Dive Com-
puter) modes.
Main Time is the current time at your home location and is normally selected as the Watch Default Time.
Alternate Time will be the current time at a remote travel location. Upon arrival at the location, Alternate Time can be interchanged
with Main Time to make it the Watch Default Time. When it is not selected to be the Default Time, it can be viewed on the Watch
ALT screen, or it can be displayed on the Watch screen with Main Time and will be referred to as Dual Time
Once Alternate Time is set, by hour differential, it will automatically change when Time of Day is set/changed. When Alternate
Time is selected to be the Watch Default Time (while at a travel location), it will change directly when Time of Day is changed and
Main (home) Time will then change by a differential opposite the one set for Alternate Time.
WATCH DEFAULT TIME, information includes (Fig. 4A, 4B, 4C):
> Battery icon, during Low Battery condition.
> Day of the Week graphic (MON, TUE, etc.).
> Time of Day (hr:min:sec) with AM (or PM) icon if 12 hour format; Main (home) or Alternate (away) with lazy 8 icon.
> Date as Month.Day (or Day.Month); or Dual Time (hr:min) if Show Dual is set for Yes.
> Alarm (speaker) icon, if the Daily Alarm is set On.
• A (< 2 sec) - to access the ALT screen and step forward through the group sequence.
• A (2 sec) - to access Log and History.
• M (2 sec) - to access FREE Surface Mode.
• M (< 2 sec) - to access the Chronograph and step back through the group sequence.
• S (< 2 sec) - to silence the Daily Alarm.
• L (< 2 sec) - to toggle the Backlight On/Off.
Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
WATCH ALT (Alternate), information includes (Fig. 5A or 5B):
> Temperature with F (or C).
> Time of Day (hr:min:sec) with AM (or PM) icon if 12 hour format; Main (home) or Alternate (away) with lazy 8 icon.; or the
Date; whichever one is not on the Main.
• A (< 2 sec) - to step forward to the Watch CDT.
• M (< 2 sec) - to step back to Watch Main Time.
• Reverts to Watch Default Time in 10 seconds if A or M is not pressed.
• L (< 2 sec) - to toggle the Backlight On/Off.
Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
WATCH CDT (Countdown Timer)
This selection provides access to a CDT for use in Watch mode.
Once set and started, it will continue to run in the background while on the surface in Watch Mode until it is turned Off or the time
counts down to 0:00 at which time the alarm will strike and it will revert to Off.
Upon accessing FREE mode or starting a dive, Watch CDT operation will be terminated and the time reset to the previous setting.
CDT Lead-in, information includes (Fig. 6):
> Graphics Go To and Cdt.
• S (< 2 sec) - to access CDT Status.
• A (< 2 sec) - to step forward to Daily Alarm Lead-in.
• M (< 2 sec) - to step back to Watch ALT.
• M (2 sec), or 2 minutes of no button action, will revert to Watch Default Time.
CDT Status, information includes (Fig. 7A/B):
> Graphic TIMR.
> Countdown Time (hr:min) with TIME icon, as >>
0:00 if no time has been set, or it completed the countdown;
hr:min set if Off and ready to start;
hr:min remaining of On with a countdown in progress.
> Graphic OFF (or ON) flashing (Fig. 7A).
Fig. 4A - DEFAULT TIME
(Main selected, no Dual)
Fig. 4B - DEFAULT TIME
(Main selected, with Dual)
Fig. 5A - WATCH ALT
(Show Dual set for No)
Fig. 5B - WATCH ALT
(Show Dual set for Yes)
Fig. 6 - CDT LEAD-IN
Fig. 7A - CDT STATUS
(upon access)
or
indicates Time
is Alternate
Fig. 4C - DEFAULT TIME
(ALT selected, no Dual)
Dual Time
(Alternate)