Filter
Top Products
To do
this,
first
press
the menu
key
seven times. Now
press
the
key
adjacent
to the "SET NOISE REJECTION" label.
The
screen at the lower
right appears.
Now
press
the
key adjacentto
the
"SET
HIGH' label. The screen will clear and return to the chart screen.
The noise should be cleared from the
display
as new echoes scroll across
the screen. If it
isn't,
you may
have a
problem
with electrical
wiring,
engine,
or transducer installation. Check with
your
local
dealer, Eagle
servicecenter,
orthe
Eaglefactorycustomerservicedepartmentfor help.
CHART NOISE
REJECTION
IS SET
NC' F: II AL
I
(SET
HIGH
a
Enter
Time/Date
The Time/Date screen needs
your
local time and
present
date. With the
numbered
keys,
enter the
present
time
first,
using
24 hour time
(2:00 pm
=
14:00,
etc.).
Next,
enterthe
present
date in the
month/day/year
format. For
example,
October
4,
1991 is entered as 10:04:1991. Make certain to enter
the entire
year,
i.e. 1991
(not 91.)
'mm
___________________
If
you
make a
mistake, press
the CLEAR
key.
This will erase the last
number. After the last number in the
year
is
entered,
the "ENTER EXIT"
label
appears.
Press the
key
next to the EXIT label if
you
need to make
a correction.
The screen
will
clear and
you
will
need to re-enter both time
and
date. Press the
key
next to the
ENTER
label
if
the time and date are
correct. This
completes
the initialization
procedure.
The
position
screen
appears
next.
SONAR MENU -PAGE 7-ASP
(Advanced
Signal Processing)
ASP is a
program
embedded in the
UltraNavGPS's
computer
that
continually
monitors the
signals
from the receiver. It determines which
echoes are
noise,
rejects
them,
allowing target
echoes to be
displayed
with a minimum of screen
clutter. This feature is
especially useful,
since
it
typically
allows
you
to
operate
the boat at all
speeds
without
adjusting
the
sensitivity.
When the UltraNavGPS is first turned
on,
ASP is enabled.
To turn ASP
off, press
the menu
key
seven
times. The menu shown at
thetop
of the next
page appears.
Now
press
the
key adjacent
tothe "Turn
Off ASP" label. The
unit
will
return to the sonar screen with ASP off. To
turn ASP on
again, repeat
the above
steps.
The
present position display
at the
top
of the screen
flashes,
indicating
that
the unit has not calculated
your latitude/longitude.
Whenthe
flashing stops,
the unit is
ready
for
navigation.
WARNING!
Never
navigate
with
this unit when the
position
screen flashes the latitude/
longitude!
This meansthe unit is not usablefor
navigation. Always
use more
than one method to
navigate.
If
you
move a
long
distance with the unit turned off from the last time
you
used the UltraNavGPS
(100
miles or
more), you may
need to re-initializethe
unit. If
you preset
the
UltraNavGPS,
you
will
definitely
need to re-initialize
the unit. The "Initial
Setup"
menu selection on the GPS' second menu
page
returns
you
to the initial
setup
menu,
when needed.
Otherwise,
you
shouldn't need to
repeat
these
steps.
28
45
SET
NOISE
REJECTION
SGlIJflI ..........,
a
SIlI]fll
eIuJEUJSiEa
H
— -
A
—
•
—
H
(HH:MM)
m
A
- -
(MM :DD :VYVY)
24 HOUR
FORMAT
-
MUSE
14:28
F
H
(HH:MF'l)
I
V12:16:1991F
<MM LID 'r"r')
ENTER EXIT
PDF compression, OCR, web-optimization with CVISION's PdfCompressor