Filter
Top Products
86
Reference Manual
IP2048/RM, Rev AA
Appendix E: Field Communicator
February 2015
Figure E-1. Field Communicator menu tree
1. Overview
2. Configure
3. Service Tools
1. Status
2. Primary Purpose
Variables
3. Shortcuts
1. Active Alerts
2. Communication Status
1. Identity
2. Communication
1. Primary Variable D900
2. Level (SV) D901
1. Device Information
2. Basic Setup
1. Device Information
2. Materials of Construction
1. Identification
2. Message
1. Transducer Material P970
1. Basic Setup
2. Present Depth
3. Apply Values
1. Guided Setup
2. Manual Setup
1. Basic Setup
2. Level
3. Profiling
4. Relay Output (*1)
5. HART/Identity
6. Engineering
7. False Echoes
8. Advanced Processing
1. Tag P001
2. Bottom Reference P010
3. Upper Range Value P015
4. Lower Range Value P016
5. Damping P020
1. Primary Variable Units P012
2. Set Non-Linear Profile
3. Non-Linear Profile P011
4. Scale Factor P013 (*4)
5. Non-Linear Profile Height P014 (*2 *3)
6. Plot Non-Linear Profile Points (*2)
1. Bottom Reference P010
2. Distance Offset P060
3. Present Depth
4. Level Offset P069
1. Relay 1
2. Relay 2
1. Lost Echo Delay P021
2. Lost Echo Action P022
3. Analog Output Alarm Type
4. Speed of Sound P024
5. Upper Blanking P023
6. Lower Blanking P063
1. Set Upper Blanking
2. Threshold
3. Set Spike Reject
4. Set Power Control
5. Set Target Pulses
6. Set Frequency
1. Number of False Echoes D980
2. Distance D910
3. Echo Size D911
4. Target Echoes D913
5. Clear False Echoes
6. Learn False Echo
7. Auto Tank Map
8. False Echo Data
9. Diagnostic Data
1. Profile Point1 P030
2. Profile Point2 P031
3. Profile Point3 P032
4. Profile Point4 P033
5. Profile Point5 P034
6. Profile Point6 P035
7. Profile Point7 P036
8. Profile Point8 P037
9. Profile Point9 P038
10. Profile Point10 P039
1. Threshold is fixed by user
2. Set Threshold
3. Threshold P026
4. Threshold in Use D917
5. Threshold is not optimum
6. Threshold 1 Time P043
7. Threshold 1 Size P048
8. Echo Size D911
9. Distance D910
10. Target Echoes D913
11. Success Rate D912
1. Poll Address D951
2. Preambles D964
1. False echoes are stored
2. False echo rejected
3. All received echoes rejected
4. No Echoes received
1. Target Pulses P044
2. Pulses in Use D918
3. Echo Size D911
4. Distance D910
5. Success Rate D912
1. Target Frequency P045
2. Transducer Frequency D916
3. Echo Size D911
4. Success Rate D912
1. Spike Reject P049
2. Echo Size D911
3. Distance D910
4. Target Echoes D913
5. Success Rate D912
1. Power Control P040
2. Power Control is active
3. Transmit Power D919
4. Echo Size D911
5. Distance D910
6. Target Echoes D913
1. Temperature
2. Dependencies
3. Internal Extremes
1. Date P003
2. Message P000
1. Tag P001
2. Model Code D949
3. Final Assembly Number P004
4. HART Revision D962
5. Device Revision D963
6. Software Revision D953
7. Hardware Revision D952
9. Set Temperature
1. Tag P001
2. Descriptor P002
3. Message P000
4. Manufacturer D960
5. Model Code D949
6. Date P003
7. Device ID D961
8. Final Assembly Number P004
9. Serial Numbar P005
1. First Distance P081
2. First Size P082
3. Second Distance P083
4. Second Size P084
5. Third Distance P085
6. Third Size P086
7. Fourth Distance P087
8. Fourth Size P088
*1 Only on MSP422.
*2 Only shown if required by selected Profile.
*3 Can say Power Factor P014 depending on selected Profile.
*4 Can say k-factor P013 depending on selected Profile.
1. Intenal temperature sensor in use
2. Remote temperature sensor in use
3. Temperature is fixed by user
4. Set Temperature
5. Temperature for Calculation D915
6. Transducer Temperature D903
7. Temperature is high
8. Temperature is low
1. Temperature has exceeded hight limit
2. Maximum temperature P046
3. Temperature has exceeded low limit
4. Minimum Temperature P047
1. Distance D910
2. Speed of Sound D914
See Next Page
1. Relay 1 Mode P070
2. Relay 1 On Point P071
3. Relay 1 Off Point P072
4. Relay 1 State
1. Relay 2 Mode P073
2. Relay 2 On Point P074
3. Relay 2 Off Point P075
4. Relay 2 State