Filter
Top Products
5-48
Constant Control mode settingChang
es dur-
ing op-
eration
Default
setting
Setting
range
Setting
unit
Regis-
ter No.
NameConstant
Flux
vector
Open
loop
vector
V/f with
PG
V/f
control
Chang
es dur-
ing op-
eration
Default
setting
Setting
range
Setting
unit
Regis-
ter No.
Name
H3-10 Gain: Terminal 14 0412 0.1 0.0 to
1,000.0
100.0 Yes Yes Yes Yes Yes
H3-11 Bias: Terminal 14 0413 0.1 –100.0 to
+100.0
0.0 Yes Yes Yes Yes Yes
H3-12 Analog input filter time
constant
0414 0.01 0.00 to 2.00 0.00 No Yes Yes Yes Yes
H4-01 Multi-function analog
output 1 selection:
terminal 21
0415 1 1 to 31 2 No Yes Yes Yes Yes
H4-02 Gain terminal 21 0416 0.01 0.00 to 2.50 1.00 Yes Yes Yes Yes Yes
H4-03 Bias terminal 21 0417 0.1 –10.0 to
+10.0
0.0 Yes Yes Yes Yes Yes
H4-04 Multi-function analog
output 2 selection:
terminal 23
0418 1 1 to 31 3 No Yes Yes Yes Yes
H4-05 Gain terminal 23 0419 0.01 0.00 to 2.50 0.50 Yes Yes Yes Yes Yes
H4-06 Bias terminal 23 041A 0.1 –10.0 to
+10.0
0.0 Yes Yes Yes Yes Yes
H4-07 Analog output signal
level selection
041B 1 0, 1 0 No Yes Yes Yes Yes
H5-01 Not used. 041C --- --- 1F --- --- --- --- ---
H5-02 Not used. 041D --- --- 3 --- --- --- --- ---
H5-03 Not used. 041E --- --- 0 --- --- --- --- ---
H5-04 Not used. 041F --- --- 3 --- --- --- --- ---
H5-05 Not used. 0420 --- --- 1 --- --- --- --- ---
Note The values in parentheses indicate initial values when initialized in 3-wire sequence.
D Protective Function (L) Parameter Constants
Constant Name Regis- Setting Setting Default Chang
Control mode setting
ter No. unit range setting es dur-
ing op-
eration
V/f
control
V/f with
PG
Open
loop
vector
Flux
vector
L1-01 Motor protection
selection
0480 1 0, 1 1 No Yes Yes Yes Yes
L1-02 Motor protection time
constant
0481 0.1 0.1 to 5.0 1.0 No Yes Yes Yes Yes
L2-01 Momentary power
loss selection
0482 1 0 to 2 0 No Yes Yes Yes Yes
L2-02 Momentary power
loss ridethru
0483 0.1 0.0 to 2.0 0.7
(See
note 1.)
No Yes Yes Yes Yes
L2-03 Minimum baseblock
time (BB)
0484 0.1 0.0 to 5.0 0.5
(See
note 1.)
No Yes Yes Yes Yes
L2-04 Voltage restart time 0485 0.1 0.0 to 5.0 0.3
(See
note 1.)
No Yes Yes Yes Yes
L2-05 Under voltage
detection level (UV)
0486 1 150 to 210
(See note 2.)
190
(See
note 2.)
No Yes Yes Yes Yes
L2-06 Not used 0487 0.1 --- 0.0 --- --- --- --- ---
L3-01 Stall prevention
during acceleration
0488 1 0 to 2 1 No Yes Yes Yes No
CompoBus/D Communications Card Operations Chapter 5