Filter
Top Products
233
Numeric
24V external power supply operation (EV)..........................197
7-speed selection (combination of RL, RM, RH) ................111
A
Acceleration time, deceleration time setting (Pr. 7, Pr. 8, Pr.
20, Pr. 21, Pr. 44, Pr. 45)....................................................116
Acceleration/deceleration pattern (Pr. 29)...........................120
Actual operation time...............................................................147
Advanced magnetic flux control (Pr. 71, Pr. 80, Pr. 81, Pr. 89,
Pr. 800).................................................................................... 95
Applied motor (Pr. 71, Pr. 450).............................................. 125
Automatic restart after instantaneous power failure/flying start
(Pr. 57, Pr. 58, Pr. 96, Pr. 162, Pr. 165, Pr. 298, Pr. 299, Pr.
611)........................................................................................151
Avoiding mechanical resonance points (frequency jumps) (Pr.
31 to Pr. 36)..........................................................................106
B
Base frequency, voltage (Pr. 3, Pr. 19, Pr. 47)................... 107
Basic operation (factory setting)..............................................75
Brake transistor alarm detection (E.BE)...............................200
C
Cable specifications................................................................... 47
Cables and wiring length .......................................................... 17
Changing the control method (Pr. 80, Pr. 81, Pr. 800) ........93
Changing the parameter setting value ...................................76
Checking the inverter and converter modules.....................214
Cleaning ....................................................................................214
Common memory ...................................................................... 54
Communication option fault (E.OP1)....................................200
Communication set status LED (CHG)................................... 49
Connecting the 24V external power supply...........................23
Connecting the FL-net dedicated cable ................................. 48
Connecting to the network........................................................47
Connection of a DC reactor (FR-HEL) ...................................28
Connection of a dedicated external brake resistor...............25
Connection of the brake unit (FR-BU2)..................................27
Control circuit terminal ..............................................................20
Converter output voltage ........................................................147
Converter output voltage peak value....................................147
Cooling fan operation selection (Pr. 244).............................176
Cooling system types for inverter enclosure .........................10
CPU error (E.5, E.6, E. 7, E.CPU) ........................................202
Cumulative energization time.................................................147
Cumulative power....................................................................147
Cyclic transmission....................................................................53
D
Daily and periodic inspection.................................................213
Daily inspection........................................................................212
DC injection brake (Pr. 10 to Pr. 12).....................................135
Detection of output frequency
(SU, FU signal, Pr. 41 to Pr. 43)........................................144
Device status LED (DEV), remote status LED (RMT) .........49
Display and erasure of communication error occurrence
count (Pr. 501)......................................................................161
Display of the life of the inverter parts
(Pr. 255 to Pr. 259)...............................................................214
Droop control (Pr. 286 to Pr. 287)..........................................173
During forward rotation..............................................................59
During reverse rotation..............................................................59
E
Earth (ground) fault detection at start (Pr. 249)...................160
Edit enabled (Edit signal) ..........................................................59
Electronic thermal O/L relay pre-alarm (TH)................123, 196
Electronic thermal relay function load factor........................147
EMC measures ...........................................................................32
Error reset....................................................................................57
Error response at word block read/write.................................61
Exhibiting the best performance for the motor (offline auto
tuning) (Pr. 71, Pr. 80 to Pr. 84, Pr. 90 to Pr. 94, Pr. 96, Pr.
859).........................................................................................127
Extended parameter display and user group function (Pr. 160,
Pr. 172 to Pr. 174)................................................................167
F
Fan alarm (FN)..................................................................176, 197
Fault (ALM signal) ......................................................................59
Fault or alarm indication..................................................147, 188
Faults history (E.---) .................................................................188
Fin overheat (E.FIN).................................................................199
FL remote communication specification .................................46
FL remote data communication types.....................................52
Forward rotation command (STF signal)................................57
Free parameter (Pr. 888, Pr. 889) .........................................181
Frequency setting value ..........................................................147
Front cover.....................................................................................5
G
General-purpose magnetic flux vector control (Pr. 71, Pr. 80,
Pr. 81, Pr. 800)........................................................................98
H
Harmonic suppression guideline in Japan..............................35
Heatsink overheat pre-alarm (FIN signal).............................199
High-speed operation command (RH signal).................57, 111
I
Input data (inverter to master)..................................................59
Input phase loss (E.ILF) ..................................................160, 199
Input/output phase loss protection selection
(Pr. 251, Pr. 872)..................................................................160
Inrush current limit circuit fault (E.IOH).................................202
Internal board fault(E.PE2) .....................................................201
Internal circuit fault (E.13).......................................................202
Inverter installation environment................................................8
Inverter output shutoff signal (MRS signal, Pr. 17).............143
Inverter output terminal monitor.....................................147, 149
Inverter overload trip (electronic thermal relay function)
(E.THT)...........................................................................123, 199
Inverter placement......................................................................11
Inverter reset (Err.)...........................................................192, 194
Inverter reset (RES signal)......................................................192
Inverter running (RUN signal)...........................................59, 142
Appendix 2 Index