Filter
Top Products
70
4.3 Adjust the output torque (current) of the motor 73
4.3.1 Manual torque boost (Pr. 0, Pr. 46) .............................................................................................. 73
4.3.2 Large starting torque and low speed torque are necessary (General-purpose magnetic flux vector
control (Pr. 71, Pr. 80)) ................................................................................................................. 75
4.3.3 Slip compensation (Pr. 245 to Pr. 247)......................................................................................... 78
4.3.4 Stall prevention operation (Pr. 22, Pr. 23, Pr. 48, Pr. 66, Pr. 156, Pr. 157).................................. 79
4.4 Limit the output frequency 83
4.4.1 Maximum/minimum frequency (Pr. 1, Pr. 2, Pr. 18)...................................................................... 83
4.4.2 Avoid mechanical resonance points (frequency jumps) (Pr. 31 to Pr. 36).................................... 84
4.5 Set V/F pattern 85
4.5.1 Base frequency, voltage (Pr. 3, Pr. 19, Pr. 47)............................................................................. 85
4.5.2 Load pattern selection (Pr. 14) ..................................................................................................... 87
4.6 Frequency setting by external terminals 89
4.6.1 Operation by multi-speed operation (Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr. 232 to Pr. 239).............. 89
4.6.2 Jog operation (Pr. 15, Pr. 16) ....................................................................................................... 91
4.6.3 Remote setting function (Pr. 59)................................................................................................... 93
4.7 Setting of acceleration/deceleration time and acceleration/
deceleration pattern 96
4.7.1 Setting of the acceleration and deceleration time
(Pr. 7, Pr. 8, Pr. 20, Pr. 44, Pr. 45) .............................................................................................. 96
4.7.2 Starting frequency and start-time hold function (Pr. 13, Pr. 571).................................................. 98
4.7.3 Acceleration/deceleration pattern (Pr. 29) .................................................................................... 99
4.8 Selection and protection of a motor 100
4.8.1 Motor overheat protection (Electronic thermal O/L relay, PTC thermistor protection) (Pr. 9, Pr. 51,
Pr. 561)....................................................................................................................................... 100
4.8.2 Applied motor (Pr. 71, Pr. 450)................................................................................................... 103
4.8.3 To exhibit the best performance of the motor (offline auto tuning)
(Pr. 71, Pr. 80, Pr. 82 to Pr. 84, Pr. 90, Pr. 96)........................................................................... 105
4.9 Motor brake and stop operation 109
4.9.1 DC injection brake (Pr. 10 to Pr. 12)........................................................................................... 109
4.9.2 Selection of a regenerative brake (Pr. 30, Pr. 70) ...................................................................... 110
4.9.3 Stop selection (Pr. 250) .............................................................................................................. 112
4.10 Function assignment of external terminal and control 113
4.10.1 Input terminal function selection (Pr. 178 to Pr. 182).................................................................. 113
4.10.2 Inverter output shutoff signal (MRS signal, Pr. 17)..................................................................... 115
4.10.3 Condition selection of function validity by second function selection signal (RT)....................... 116
4.10.4 Start signal operation selection (STF, STR, STOP signal, Pr. 250) ........................................... 117
4.10.5 Output terminal function selection (Pr. 190, Pr. 192).................................................................. 119
4.10.6 Detection of output frequency (SU, FU signal, Pr. 41 to Pr. 43)................................................. 123
4.10.7 Output current detection function
(Y12 signal, Y13 signal, Pr. 150 to Pr. 153, Pr. 166, Pr. 167) .................................................... 124
Parameters according to purposes