xStack
®
DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual
311
The IGMP and MLD Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate
parameters) in the following table.
Command Parameters
config igmp_snooping [vlan_name <vlan_name 32> | all] {host_timeout <sec 1-16711450> |
router_timeout <sec 1-16711450> | leave_timer <sec 1-16711450> | state
[enable | disable] | fast_leave [enable | disable] | report_suppression [enable |
disable]}(1)
config igmp_snooping querier [vlan_name <vlan_name 32> | all]{ query_interval <sec 1-65535> |
max_response_time <sec 1-25> | robustness_variable <value 1-255> |
last_member_query_interval <sec 1-25> | state [enable | disable]| version
<value 1-3> }
config router_ports <vlan_name 32> [add | delete] <portlist>
config router_ports_forbidden <vlan_name 32> [add | delete] <portlist>
enable igmp_snooping {forward_mcrouter_only}
disable igmp_snooping {forward_mcrouter_only}
create igmp_snooping static_group [vlan<vlan_name 32> | vlanid <vlanid_list> ] <ipaddr>
delete igmp_snooping static_group [vlan<vlan_name 32> | vlanid <vlanid_list> ] <ipaddr>
config igmp_snooping static_group
[vlan <vlan_name 32> | vlanid <vlanid_list> ] < ipaddr > [ add | delete] <portlist>
show igmp_snooping static_group {[vlan <vlan_name 32> | vlanid <vlanid_list>] < ipaddr >}
show igmp_snooping {vlan <vlan_name 32>}
show igmp_snooping group {vlan <vlan_name 32>}
show igmp_snooping forwarding {vlan <vlan_name 32>}
show router_ports {vlan <vlan_name 32>} {static | dynamic | forbidden}
config mld_snooping [vlan_name <vlan_name 32>| all] {node_timeout <sec 1-16711450> |
router_timeout <sec 1-16711450> | done_timer <sec 1-16711450> | state
[enable | disable] | fast_done [enable | disable]}(1)
config mld_snooping querier [vlan_name <vlan_name 32> | all] {query_interval <sec 1-65535> |
max_response_time <sec 1-25> | robustness_variable <value 1-255> |
last_listener_query_interval <sec 1-25> | state [enable | disable] | version <value
1-2> }(1)
config mld_snooping mrouter_ports
vlan <vlan_name 32> [add | delete] <portlist>
config mld_snooping
mrouter_ports_forbidden
vlan <vlan_name 32> [add | delete] <portlist>
enable mld_snooping {forward_mcrouter_only}
disable mld_snooping {forward_mcrouter_only}
show mld_snooping {vlan <vlan_name 32>}
show mld_snooping group {vlan <vlan_name 32>}
show mld_snooping forwarding {[vlan <vlan_name 32> | vlanid <vlanid_list>]}
show mld_snooping mrouter_ports vlan <vlan_name 32> {[static | dynamic | forbidden]}
Each command is listed, in detail, in the following sections.
config igmp_snooping
Purpose Used to configure IGMP snooping on the switch.
